Zelmer ZIR2620, User Manual

Page: 7 / 41

13
12
PL PL EN EN
MARKING MATERIAL, FOR EXAMPLE
Do not iron this material
• (1 dot) Synthetics, Nylon, Acrylics, Polyester, Rayon
• • (2 dots) Wool, Silk
• • • (3 dots) Cotton, Linen
Insert the main plug into the wall socket. The indicator light (10) will turn on.
When the indicator light goes out you may start ironing.
If you set the temperature control to lower setting after ironing at a high temperature. it is not recommended
to iron before the pilot light switches on again.
WATER TANK FILLING
Unplug the iron from the mains before filling the water tank.
The iron has been designed to use normal tap water. If the tap water in your area is hard or semi-hard,
mix tap water with distilled or demineralized water purchased in stores in the ratio 2:1 and 1:1 respectively
(distilled water / tap water).
You can inquire about the water hardness with your local water supplier.
Never use 100% distilled or demineralized water, rain water, softened water, scented water, water from
refrigerators and air conditioners, dryers or other types of home water preparation water.
Open the water inlet lid (4).
Slowly pour water through the water inlet.
Never fill beyond the level mark for maximum filling (6), in order to avoid spilling out of water.
Close the water inlet lid.
Important: The water tank should be emptied after each use.
SPRAYING
This can be used to remove stubborn wrinkles.
As long as there is enough water in the water tank, you may use the spray button at any temperature setting
during steam or dry ironing.
Press the spray button (1) several times to activate the pump while you are ironing.
Do not use the spray function with silk!
STEAM IRONING
Set the temperature control (7) to the desired position in accordance with the manufacturer’s label. The pilot
light (10) will turn on until the temperature is reached. Then the pilot light will turn off.
Set the variable steam regulator (3) to the desired position.
Temperature control (7) Recommended position of the steam
regulator (3)
MIN
CAUTION: Avoid coming in contact with ejected steam.
DRY IRONING
The steam iron can be used on the dry setting with or without water in the water tank.
Turn the steam regulator (3) to the minimum position.
Select the setting on the temperature control (7) best suited for the fabric to be ironed.
CAUTION: If the steam iron has been used for a long time, it is hot and there is no water. Do not refill it with
water until the steam iron cools down.
SHOT OF STEAM
The shot of steam feature provides additional steam for removing stubborn wrinkles.
Set the temperature control (7) to “MAX”.
Press the shot of steam button (2) to release the burst of steam.
NOTE: To prevent water leakage from the soleplate, do not keep the steam button pressed for more than
5 seconds.
VERTICAL IRONING
This can be used to remove creases from hanging clothes, curtains etc.
Hang article of clothing on a clothes hanger.
Set the temperature control (7) to “MAX”.
Operate the iron in a vertical position at a distance of 10 cm / 4 in, and press the shot of steam
button (2) repeatedly with pauses of at least 5 seconds.
NOTE: To prevent water leakage from the soleplate, do not keep the steam button pressed for more than
5 seconds.
ANTI-DRIP SYSTEM
With the anti-drip system, you can perfectly iron even the most delicate fabrics.
Always iron these fabrics at low temperatures. The plate may cool down to the point where no more steam
comes out, but rather drops of boiling water that can leave marks or stains. In these cases, the Anti-drip
system automatically activates to prevent vaporization, so that you can iron the most delicate fabrics without
risk of spoiling or staining them.
WHEN YOU FINISH IRONING
Set the temperature control (7) to the minimum position.
Remove the main plug from the wall socket.
Empty the water tank.
Stand the iron on heel rest.