Zelmer SB1001, User Manual

Page: 49 / 50

53
SB1001-001_v01
Make sure that the stand blender is clean before
using it to crush ice. Should it be dirty, wash it
thoroughly with clean water. Any washing-up
liquid residues may affect the taste of the
crushed ice and the taste of a drink, to which
such ice will be added.
To obtain the best results of running the appliance in the “ICE”
mode, use 10-25 ice cubes per load (the cubes should not be
bigger than 2 cm in size). Add also ca. 15 ml (1 teaspoonful)
of cold, fresh water. Place the jug lid and insert the stopper,
and then press the “ICE” button to run the appliance in the
momentary work mode. When the appliance has completed
ca. 5 crushing cycles, press the “ICE” button again to stop
the appliance. If you are still dissatisfied with the results of
crushing, because you want the ice to look like snow, press
and hold the “PULSE” button for a couple of seconds.
Always pour some water into the jug before
you start crushing ice.
Immediately after the crushing of ice or use
a mixer with loads of ice do not wash the
blender pitcher in hot water, because a large
temperature difference can break the glass.
Attachment for centrifuging juice from
soft fruit and soy beans
The attachment (10) is used for centrifuging juice from soft
fruit; it can also be used for preparing soy milk.
Never try to centrifuge juice from fruit with
pips, seeds or stones without removing the
latter first.
1 Mount the blender jug onto the motor unit (see
“CONTROLS AND OPERATION”).
2 Insert the attachment (10) into the blender jug (5) so that
the runners inside the jug (5) get through the cut-outs in the
attachment flange (10) . Press hard.
3 Place the lid on the jug in a manner allowing you to pour
its content out through the lid sieve.
4 Insert fruit through the opening (cut the fruit into smaller
pieces before inserting them).
5 Insert the lid stopper (9) into the opening in the lid and
turn it clockwise to lock it in place.
6
Keep blending until you are satisfied with the result.
Satisfactory results are usually obtained after ca. 60 seconds.
The stand blender should not be running
continuously for more than 60 seconds. Switch
the appliance off after 60 seconds, and wait
another 60 seconds before you run it again.
In case of fruit with little pulp some water or
another liquid such as milk or juice should be
added.
C
The jug handle (6) should be on the right side
of the appliance.
5 Put ingredients into the blender jug (5) . Do not exceed
the 1500 ml line on the blender jug. If the line is exceeded,
the content of the jug may raise jug lid (7) when the motor
is on.
The way you insert the ingredients into
a blender’s jug is free, but better results are
obtained by adding the hard components at
first.
6 Place the lid (7) onto the jug (5) before use so that its
protruding element fits in the cut-out in the jug. Press the lid
hard.
Moisten the sealing ring with water before
placing the lid (7).
7 Insert the lid stopper (9) into the opening in the lid, and
turn it clockwise to lock it in place.
Do not start the stand blender without the lid
stopper (9) in place, especially if you want
to blend solid ingredients, as they might be
ejected through the opening.
8 Start the blending by setting the knob (a) in the required
position ( MIN , , MAX ).
The stand blender should not be running
continuously for more than 60 seconds. Switch
the appliance off after 60 seconds, and wait
another 60 seconds before you run it again.
9 Set the speed regulation knob in the ”OFF” position to
stop the appliance.
QUICK START PROGRAMMES
Set the knob in the “ON” position to use one
of the three available quick start programmes
(“PULSE”, “JUICE”, “ICE”). The illuminated
ring will go on, and the program selection
buttons will start blinking. Then press the
required button.
10
„PULSE”
The appliance will start processing ingredients at a maximum
speed, if the ”PULSE” button is pressed and held. When the
button is released, the appliance will stop immediately.
11
„JUICE”
The ”JUICE” programme enables the user to prepare
delicate juices. The appliance will start processing ingredients
at a maximum speed, if the ”JUICE” button is pressed. Press
the ”JUICE” button again to stop the appliance.
12 „ICE”
You can use the “ICE” programme to crush ice. This function
allows to obtain small pieces of ice of similar size.