Zelmer jp1600-001, User Manual

Page: 45 / 48

51
JP1600-001_v03
Prepare the appliance for use (assemble)
D
1 Replace the rubber plug (2c) in the hole on the bottom of
the bowl (2) .
2
Replace the sealing sleeve (2f) in the bowl (2) , if
previously removed.
3 Mount the bowl (2) on the motor unit (1) so that three
tabs on the motor unit (1) slide into the three slots on the
bottom of the bowl (2) .
4
Install rubber wipers (3h) on the squeezing screw (3) .
5 Put the squeezing screw (3) into the bowl (2) .
6
Place the hopper (4) on the bowl (2) , sliding the tabs into
the bowl slots and turn the hopper (4) fully clockwise .
7 Insert pusher (5) into the hopper (4) .
8 Place pitchers (6) under the juice spout (2e) and pulp
ejection outlet (2d) .
Start up and use the appliance
E
Juice Maker rocker switch positions are shown in
Figure B
„ON” – turn on the appliance.
„OFF” – turn off the appliance.
„REV” – reverse mode.
●
Make sure the rocker switch (1a) is set in „OFF” position.
1 Plug in the appliance.
2 Put chopped fruits or vegetables into the hopper and
gently push with the pusher.
Do NOT push products with your fingers or
other objects.
Thoroughly wash fruits and vegetables,
remove seeds or other hard fractions before
placing products in the appliance.
3 Turn on the appliance on by placing the rocker switch
(1a) in „ON” position.
Do not touch the rocker switch (1a) with wet
hands.
Lid with hopper (4) must be securely locked
, otherwise the appliance will not start.
4
Put more chopped fruits or vegetables into the hopper
and gently push with the pusher.
The maximum weight of fruits and vegetables
placed in the Juice Maker should not exceed
250 g for each minute of operation. If the
squeezing screw gets stuck or clogged with
fruits or vegetables use the “REV” function for
2-3 seconds. If the problem persists, take the
appliance apart, clean and re-assemble (see
“Prepare the appliance for use (assemble)”).
After use (squeezing juice)
F
1
Turn off the appliance on by placing the rocker switch
(1a) in „OFF” position.
2 Unplug power cord from wall outlet.
3 Plug the juice spout (2e) using the plug (2g) before
removing the pitcher from under the juice spout (2e) . This will
prevent the juice from dripping on the kitchen worktop.
●
Pour the squeezed juice from the pitcher into glasses,
cups, etc.
If you want to rinse the appliance before
squeezing other fruits, you must first turn off
the appliance, replace the juice pitcher, turn the
appliance on again and pour a glass of water in
the hopper to rise out most of the residual pulp.
●
Take apart the appliance (see „Before Use (take
apart)” ).
Maintenance
●
Thoroughly wash the appliance after each use, preventing
any juice or residual fruit or vegetable pulp from drying.
●
Remove residue from crevices or corners using the
brush supplied with the juice maker.
●
Wipe the motor unit with a damp cloth and a few drops of
dishwashing liquid. Then wipe it dry.
If any water or juice penetrates into the motor
unit unplug the appliance and return it to
a service centre for inspection.
●
All items such as: a bowl (2) sealing sleeve (2f) , juice
spout plug (2g) , squeezing screw (3) , rubber wipers (3h) ,
hopper (4) , pusher (5) , and pitcher (6) should be washed
in warm water with dishwashing liquid.
●
When cleaning the appliance do not use detergents
containing organic solvents, bleach, chlorine, gasoline or
other abrasive materials.
●
After prolonged use the plastic elements of the appliance
may become discoloured. This is not a defect.
●
Any discolouration from carrots can be removed with
a cloth soaked in cooking oil.
●
Thoroughly dry all appliance components after washing.
●
Assemble the appliance as described earlier (see
„Prepare the appliance for use (assemble)” ).
What to do if…
Juicer Maker will not work:
1. Make sure the Juice Maker is plugged into a wall outlet.
2. Make sure the Juice Maker correctly assembled as
described in the manual.
3. Juice Maker may have turned off because it was used for
more than 20 minutes.
4. Take the appliance to a service centre.