49
ATTENTION! Due to safety reasons it is prohibited to
install a moist or damaged basic HEPA 12 filter (13).
3
After cleaning and drying the protective mesh and the
basic HEPA 12 filter, install the protective mesh on the HEPA
12 filter and insert the whole unit to the “CYKLON” dust
container.
4
Press the interlock button and turn the basic HEPA 12
filter
(13)
in the LOCK direction.
Insert the “CYKLON” dust container together with the
installed basic HEPA 12 filter
(13)
into the vacuum cleaner
chamber and close the cover by pressing it until you hear
a characteristic “click” according to section
(E)
.
HEPA 11 OUTLET FILTER
1
To replace the HEPA 11 filter lift the vacuum cleaner
handle and open the accessory compartment.
2
Grab the filter cover by the fastening, firmly pull with the
thumb and lift it upwards.
3
Remove the HEPA 11 filter case and replace it with a new
one. The HEPA filter ensures an effective operation of the
vacuum cleaner for about 1 year.
4
Insert the cover so that the two protrusions in the lower
part of the cover are inserted in the openings of the vacuum
cleaner body, press the filter cover so that the rear fastenings
snap shot on the body.
INLET FILTER
Release the upper cover fastening
●
(12)
and open the
cover.
Remove the SAFBAG dust bag module/the “CYKLON”
●
dust container from the vacuum cleaner chamber.
1
Slide the inlet filter casing with the installed inlet filter
from the tracks on the back side of the vacuum cleaner
chamber.
2
Remove the inlet filter
(19)
from the inlet filter casing.
3
Place the new filter in the inlet filter casing
(20)
with the
material side directed towards the inside of the casing.
4
Slide the inlet filter casing
(20)
together with the filter in
the tracks until stop to the previous position.
ATTENTION! Always replace a damaged inlet filter (19)
with a brand new, original one.
Insert the SAFBAG dust bag module/the “CYKLON” dust
●
container into the vacuum cleaner chamber.
Close the cover by pressing it until you hear
●
a characteristic click.
Special accessories
The following special accessories may be purchased in retail
outlets:
Zelmer turbobrush (25)
May be used with all types of ZELMER vacuum cleaners. Is
used for an effective vacuuming of carpets and fitted carpets.
While using the turbobrush follow the instruction manual.
F
G
H
The use of the turbobrush decidedly increases the
effectiveness of removing fibrous dirt such as: animal hair,
hair, threads etc. It is practically useful in households with
pets (cats, dogs), where removing the animal hair from the
carpets and floorings is very onerous.
End of operation cleaning and
maintenance
1
Switch off the vacuum cleaner by pressing the “on/off”
button
(7)
.
2
Unplug the appliance.
3
Wind the cord by pressing the cord rewind button
(4)
.
While doing this hold the cord to make sure it is not tangled
and the plug does not hit the vacuum cleaner housing.
4
Disconnect the telescopic tube from the nozzle or brush.
5
Disconnect the telescopic tube from the hose.
6
Press the two side buttons on the end of the hose and
remove the hose end from the inlet opening of the vacuum
cleaner.
7
The vacuum cleaner may be stored vertically or
horizontally. In order to do so, insert the fastening hook of
the combination brush to the combination brush fastener.
The hose may be attached to the vacuum cleaner, however
you have to make sure that it is not excessively bent during
storing.
8
If necessary wipe the housing and the dust bag container
with a damp cloth (it may be soaked with dishwashing liquid)
and dry it or wipe until dry.
Do not use abrasive detergents or solvents.
Examples of problems while operating the
vacuum cleaner
PROBLEM
ACTION
A characteristic “fluttering”
of the vacuum cleaner is
heard.
• Check the dust bag and the
accessories, remove the cause of the
clogging or replace the dust bag with
a new one.
• Clean the vacuum cleaner chamber
and the filter.
The dust bag is damaged. Remove the dust bag and the filters.
The electrical installation
fuse went out.
Check if other appliances are not
plugged to the same electrical circuit
as the vacuum cleaner. If the fuse
goes out repeatedly, return the vacuum
cleaner to a service point.
The vacuum cleaner does
not operate; the housing or
the cord is damaged.
Return the vacuum cleaner to
a service point.
The suction power of the
vacuum cleaner is weak.
Replace the dust bag and the filters,
check the suction tube, the hose and
the nozzle remove the cause of the
clogging.
Downloaded From Vacuum-Manual.com Manuals
