background image

10

HDVI5 Component Video Switch 

11

HDVI5 Component Video Switch

Controlling the Front Panel Lights

There are four different front panel light modes available on the 
HDVI5. They are:

Front panel lights automatically fade from bright to dim 

after  seconds of inac tivity.
Front panel lights are always at the bright level.
Front panel lights are always at the dim level.
Front panel lights are turned off.

Note: 

The intensities of the both the bright and dim levels can be 
adjusted as well, this is explained on the nex t page.

To change the front panel lighting mode...

Step 1: Enter the Setup Mode

The HDVI5 is placed into the setup mode by pressing and 

holding the Power button for about  seconds.

Step 2: Select the Lighting Mode option

Press the ‘’ button to selec t the “Lighting Mode” option.
The front panel selec tion LEDs now indicate the currently 

selec ted light mode as follows:
If ‘1’s blue LED is lit, then front panel lights are always off.
If ‘2’s blue LED is lit, then front panel is always dim.
If ‘’s blue LED is lit, then front panel is always bright.
If ‘’s blue LED is lit, then front panel lights auto -fade from 

bright to dim after  seconds of inac tivity.

Step 3: Choose a new lighting mode

Choose a new light control mode by pressing the associ-

ated selec tion button.
Press the Power Button to save the new mode and return to 

normal operations.

Note: 

The lighting mode setting is saved in non-volatile mem-
or y and is not affec ted by a power failure.

Turn to the nex t page for instructions on how to 

adjust LED intensities...



1                        2                        3                        4                        5                      SEL                     A1          A2

Step 1: Place the HDVI5 into the Setup Mode

Press and hold the Power Button until the 

display goes wild.  (About  seconds.)

Step 2: Select “Lighting Mode” option

1                        2                        3                        4                        5                      SEL                     A1          A2

After ‘’ is pressed, the standby 
LED continues to flash, and the 
front panel will display the cur-
rent Light Mode settings.

Step 3: Choose a new lighting mode

1                        2                        3                        4                        5                      SEL                     A1          A2

Auto-Fade
Always Bright 
Always Dim
Always Off

Exit Setup Mode

All manuals and user guides at all-guides.com

Summary of Contents for HDVI5




















Reviews: