background image

 

Laser Warning 

 

WARNING: Class II Laser product. Avoid long-term viewing of 

direct laser radiation. Prolonged staring into the beam (direct or 

reflected) can damage the retina. 

 

This system uses a class II laser which is considered eye and skin safe but can cause eye 

damage if exposed directly for a extended time. Natural human reflexes will normally 
make the subject blink or look away before any damage is inflicted to the eyes. Any use 

other than those specified in this document could result in hazardous laser radiation 

exposure.  
 

Use the following usage precautions: 

 

 

Never stare into the beam, neither directly nor from a mirror-like surface. Human 

skin is not considered as a reflective surface. 

 

MEDICAL USAGE: warn subjects not to stare into the beam. Subjects under 
effect of any medication and young children could possibly have their 

natural aversion reflex affected and it may be advised to wear a 

blindfold. 

 

The ZScanner 800 should NEVER be opened for any reason as there are no 

internal adjustments. In case of a malfunction, contact the manufacturer or 
distributor. 

 

 

CAUTION NOTES 

 
PLEASE READ THE COMPLETE MANUAL BEFORE USE. OPERATING YOUR ZScanner 800 LASER 

SCANNER USING PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN 

HAZARDOUS RADIATION EXPOSURE. 
 

AVOID DIRECT EYE CONTACT WITH THE LASER BEAM. 

 
ELECTROSTATIC DISCHARGES COULD DISCONNECT THE DEVICE. 

 
DISREGARDING ANY OF THE RULES AND CARE RECOMMENDATION INCLUDED IN THIS 

MANUAL MAY VOID THE SYSTEM WARRANTY. 

 
Please read and follow all WARNING statements throughout this manual 

User License 

Summary of Contents for ZScanner




















































Reviews: