background image

Disclaimer 

Yuneec International (China) Co., Ltd shall not be held liable for any damage, injury or for use of the 
product in violation with legal regulations, especially in the following circumstances: 
Damage and/or injury as well violation of legal regulations resulting from a failure to comply with the 
operating instructions or the instructions at www.yuneec.com, product information, user manual and 
other legally binding information;
Damage and/or injury as well violation of legal regulations brought about by the influence of alcohol, 
drugs, medication or other narcotics which may impact on the concentration of the user;
The same applies to illnesses effecting the concentration of the user (dizziness, tiredness, nausea etc.) 
or other factors compromising mental and physical capabilities.
Intentionally caused damage, injury or violation of legal regulations;
Any request for compensation caused by an accident resulting from use of the product;
Malfunction of the product caused by retrofitting or replacement with components which did not 
come  from Yuneec;
Damage and/or injury caused by the use of replica parts (non-original parts);
Damage and/or injury as well as violation of legal regulations caused by incorrect operation or mis-
judgment;
Damage and/or injury caused by damaged spare parts or not using original Yuneec spare parts;
Damage and/or injury caused by unauthorized change settings and/or parameters;
Damage and/or injury caused by modify and/or add parts;
Damage and/or injury as well as violation of legal regulations caused by ignoring the low voltage bat-
tery warning;
Damage and/or injury caused by knowingly and negligibly flying with a damaged model or one which 
is unfit to fly, e.g. due to dirt, water penetration, coarse particles, oil or a model which has not been 
correctly or completely assembled or if the main components exhibit visible damage, defects or miss-
ing parts;
Damage and/or injury as well as violation of legal regulations caused by use of the product in a no-fly 
zone, e.g. next to an airfield, above a motorway or a natural conservation area;
Damage and/or injury as well as violation of legal regulations caused by operating the model in a 
magnetic field (e.g. high voltage lines, electricity/ transformer stations, radio towers, mobile phone 
masts etc.), a strong wireless signal environment, no-fly zones, poor visibility and in the event of 
vision impairments or other impacts on the pilot which are left unchecked etc;
Damage and/or injury brought about through a violation of the legal regulations for operating the 
model, in unsuitable weather conditions, e.g. rain, wind, snow, hail, storms, hurricanes etc;
Damage and/or injury as well as violation of legal regulations caused by force majeure, e.g. collision, 
fire, explosion, flooding, tsunami, landslide, avalanche, earthquake or other forces of nature;
Damage and/or injury as well as violation of legal regulations caused by the illegal or immoral use of 
the model, e.g. capturing videos or recording data which infringes upon/harms the privacy of other 
people;
Damage and/or injury as well as violation of legal regulations caused by incorrect use of the batteries, 
protection systems, chargers or aircraft;
Consequential damage caused by the incorrect operation of any kind of system components and ac-
cessory parts, especially memory cards, whereby image or video material from the camera can 
become defect;
Any non-compliance with legal obligations, personal injury, material damage and environmental 
damage caused by use and a failure to comply with the local laws and regulations;
Damage and/or injury as well as violation of legal regulations caused by hazardous use without suffi-
cient practical experience;
Damage and/or injury as well as violation of legal regulations caused by flying in legally defined 
no-fly zones.
Further losses which do not fall within the scope of use defined by Yuneec as improper.
This product is designed for both professional use and personal private use. The national and 
international laws and regulations in force as the time of taking off must be adhered to.

Collection and Processing of Data

Yuneec may collect navigation information such as GPS data to help improve our products. 
We may also collect Depth Map information and Infrared Image information from your drone deliv-
ered to our service center for repair and maintenance service or any other service. 
We may also collect other information such as device information, server log information, etc. We 
may also collect personal information used in registration if you choose to become a registered user 
and any other information user provided to Yuneec. We may also collect information which user send 
to other users, and the recipients and senders of such information.
We reserve the right to disclose your information if required to do so by law or in the good-faith belief 
that such disclosure is needed to comply with applicable laws, for example in response to a court 
order, judicial subpoena, warrant or request from government, or otherwise cooperating with govern-
ment agencies or law enforcement. 
We also reserve the right to disclose your information that we believe in good faith is necessary or 
appropriate to: (i) protect ourselves or others from fraudulent, unlawful, or abusive activities; (ii) take 
precautions against potential liability; (iii) protect the security of the Yuneec Apps embedded into or 
downloaded onto your drone or any associated equipment and services; (iv) protect the legal rights of 
ourselves or any others.
Any information we collected maybe disclosed or transferred to an acquirer, successor or assignee as 
part of any potential merger, acquisition, debt financing or other activities that involves transfer of 
business assets.
We may make the aggregated non-personal information of the users available to third parties for vari-
ous purposes, including (i) complying with various report obligations; (ii) marketing efforts; (iii) ana-
lyzing product safety; (iv) understanding and analyzing our users’ interests, habits, usage pattern for 
certain functionalities, services, content, etc.

Battery Warnings and Usage Guidelines

WARNING: 

Lithium Polymer (LiPo) batteries are significantly more volatile than alkaline, NiCd or 

NiMH batteries. All instructions and warnings must be followed exactly to prevent property damage 
and/or serious injury as the mishandling of LiPo batteries can result in fire. By handling, charging or 
using the included LiPo battery you assume all risks associated with LiPo batteries. If you do not 
agree with these conditions please return the complete product in new, unused condition to the place 
of purchase immediately.
You must always charge the LiPo battery in a safe, well-ventilated area away from flammable materials.
Never charge the LiPo battery unattended at any time. When charging the battery, you must always 
remain in constant observation to monitor the charging process and react immediately to any poten-
tial problems that may occur.
After flying/discharging the LiPo battery you must allow it to cool to ambient/room temperature 
before recharging.
To charge the LiPo battery you must use only the included charger or a suitably compatible LiPo bat-
tery charger. Failure to do so may result in a fire causing property damage and/or serious injury.
If at any time the LiPo battery begins to balloon or swell, discontinue charging or discharging imme-
diately. Quickly and safely disconnect the battery, then place it in a safe, open area away from flam-
mable materials to observe it for at least 15 minutes. Continuing to charge or discharge a battery that 
has begun to balloon or swell can result in a fire. A battery that has ballooned or swollen even a small 
amount must be removed from service completely.
Do not over-discharge the LiPo battery. Discharging the battery too low can cause damage to the bat-
tery resulting in reduced power, flight duration or failure of the battery entirely. LiPo cells should not 
be discharged to below 3.0V each under load.
Store the LiPo battery at room temperature and in a dry area for best results.
When charging, transporting or temporarily storing the LiPo battery the temperature range should be 

from approximately 40–120 ° F (5–49 ° C). Do not store the battery or aircraft in a hot garage, car or 
direct sunlight. If stored in a hot garage or car the battery can be damaged or even catch fire.
Never leave batteries, chargers and power supplies unattended during use.
Never attempt to charge low voltage, ballooned/swollen, damaged or wet batteries.
Never allow children under 14 years of age to charge batteries.
Never charge a battery if any of the wire leads have been damaged or shorted.
Never attempt to disassemble the battery, charger or power supply.
Never drop batteries, chargers or power supplies.
Always inspect the battery, charger and power supply before charging.
Always ensure correct polarity before connecting batteries, chargers and power supplies.
Always disconnect the battery after charging.
Always terminate all processes if the battery, charger or power supply malfunctions.

General Safety Precautions and Warnings

WARNING:

 Failure to use this product in the intended manner as described in the quick start guide 

and instruction manual can result in damage to the product, property and/or cause serious injury. A 
Radio Controlled (RC) multirotor aircraft, APV platform, drone, etc. is not a toy! If misused it can 
cause serious bodily harm and damage to property.

WARNING:

 As the user of this product you are solely and wholly responsible for operating it in a manner 

that does not endanger yourself and others or result in damage to the product or the property of others.
Keep your hands, face and other parts of your body away from the spinning propellers/rotor blades 
and other moving parts at all times. Keep items that could impact or become entangled away from 
the propellers/rotor blades including debris, parts, tools, loose clothing, etc.
Always operate your aircraft in open areas that are free from people, vehicles and other obstructions.
Never fly near or above crowds, airports or buildings.
To ensure proper operation and safe flight performance never attempt to operate your aircraft nearby 
buildings or other obstructions that do not offer a clear view of the sky and can restrict GPS reception.
Do not attempt to operate your aircraft in areas with potential magnetic and/or radio interference 
including areas nearby broadcast towers, power transmission stations, high voltage power lines, etc.
Always keep a safe distance in all directions around your aircraft to avoid collisions and/or injury. This 
aircraft is controlled by a radio signal subject to interference from many sources outside your control. 
Interference can cause momentary loss of control.
To ensure proper and safe operation of the automatic landing function in Return Home Mode you 
must start the motors with the aircraft in an open space and achieve a proper GPS lock.
Do not attempt to operate your aircraft with any worn and/or damaged components, parts, etc. 
including, but not limited to, damaged propellers/rotor blades, old batteries, etc.
Never operate your aircraft in poor or severe weather conditions including heavy winds, precipitation, 
lightning, etc.
Always begin to operate your aircraft with a fully charged battery. Always land as soon as possible 
after the first level low voltage battery warning or land immediately after the second level low voltage 
battery warning.
Always operate your aircraft when the voltage of the battery in the transmitter/personal ground station is in 
a safe range (as indicated by the LED status indicator light of the transmitter/personal ground station).
Always keep the aircraft in clear line of sight and under control, and keep the transmitter/personal 
ground station powered on while the aircraft is powered on.
Always move the throttle control stick down fully and turn off the power in the event the propel-
lers/rotor blades come into contact with any objects.
Always allow components and parts to cool after use before touching them and flying again.
Always remove batteries after use and store/transport them per the corresponding guidelines.
Avoid water exposure to all electronic components, parts, etc. not specifically designed and protected 
for use in water. Moisture causes damage to electronic components and parts.
Never place any portion of the aircraft or any related accessories, components or parts in your mouth 

IC Radiation Exposure Statement for Canada

This device complies with Industry Canada license-exempt RSS standard (s).Operation is subject to 
the following two conditions: (1) this device may not cause interference, and (2) this device must 
accept any interference, including interference that may cause undesired operation of the device.Le 
présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de 
licence. L'exploitationestautorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire 
de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout brouillageradioélectriquesubi, mêmesi 
le brouillageest susceptible d'encompromettre le fonctionnement.
This equipment complies with IC RSS-102 radiation exposure limit set forth for an uncontrolled envi-
ronment. Cetéquipementrespecte les limitesd'exposition aux rayonnements IC définies pour un envi-
ronnement non contrôlé.

NCC Warning Statement

本產品符合低功率電波輻射性電機管理辦法 第十二條 ~ 第十四條等條文規定:

* 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更

原設計之特性及功能。

* 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無

干擾時方得繼續使用。

前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電

波輻射性電機設備之干擾。

CE Warning Statement

This device meets the EU requirements on the limitation of the general public to electromagnetic 
fields by way of health protection.
EU Operation Frequency (The Maximum Transmitted Power)
ST16S Remote Controller:
2.4G: 2405-2475MHz (20dBm);
2.4G Wifi: 2412-2472MHz (20dBm);
5G Wifi: 5560-5580MHz (27dBm), 5680-5700MHz (27dBm)
TYPHOON H3: 
2.4G:2405-2475MHz (20dBm)
ION L1 PRO:
5G Wifi: 5560-5580MHz (27dBm), 5680-5700MHz (27dBm)

EU Compliance Statement

Hereby, Yuneec International (China) Co., Ltd. declares that this device is in compliance with the essen-
tial requirements and other relevant provisions of the RED Directive 2014/53/EU. The full text of the EU 
Declaration of Conformity is available at the following internet address: http://yuneec/de-downloads
Please visit the address above and enter corresponding product page.

as doing so could cause serious injury or even death.
Always keep chemicals, small parts and electronic components out of the reach of children.
To ensure safe fly, it is recommended to install the propeller protectors when operating the aircraft 
indoors or nearby crowds.
Carefully follow the instructions and warnings included with this aircraft and any related accessories, 
components or parts (including, but not limited to, chargers, rechargeable batteries, etc.).

Camera Usage Warnings

NOTICE

For the latest product information, please check our official website: 

www.yuneec.com.

WARNING

Do not expose the lens of the camera to extreme light sources.
Do not operate the camera in the rain or in environments with high humidity.
Do not try to repair the camera. Repairs must go to an authorized service center.

WARNING

Read the entire instruction manual to become familiar with the features of the product before operating.
Do not use with incompatible components or alter this product in any way outside of the instructions 
provided by Yuneec.
Failure to use this product in the intended manner as described in instruction manual can result in 
damage to the product, property and/or cause serious injury.

FCC Statement

This equipment has been tested and found to comply with the limits for Part 15 of the FCC rules. 
These limits are designed to provide reasonable protection against harmful interference in a residen-
tial installation. This equipment generates, uses and can radiate radio frequency energy and, if not 
installed and used in accordance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not occur in a particular installa-
tion. If this equipment does cause harmful interference to radio or television reception, which can be 
determined by turning the equipment off and on, the user is encouraged to try to correct the interfer-
ence by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and (2) this device must accept any interference 
received, including interference that may cause undesired operation.

RF Exposure Warning

This equipment must be installed and operated in accordance with provided instructions and the an-
tenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm 
from all persons and must not be co-located or operating in conjunction with any other antenna or 
transmitter. End-users and installers must be provided with antenna installation instructions and 
transmitter operating conditions for satisfying RF exposure compliance.

44                                

Summary of Contents for TYPHOON H3


















































Reviews: