FORM NO.:6U6K-B01E-NB-EN
JOHNSON CONTROLS
2
IMPORTANT!
READ BEFORE PROCEEDING!
GENERAL SAFETY GUIDELINES
This equipment is a relatively complicated apparatus.
During rigging, installation, operation, maintenance, or
service, individuals may be exposed to certain
components or conditions including, but not limited to:
heavy objects, refrigerants, materials under pressure,
rotating components, and both high and low voltage.
Each of these items has the potential, if misused or
handled improperly, to cause bodily injury or death. It
is the obligation and responsibility of rigging,
installation, and operating/service personnel to identify
and recognize these inherent hazards, protect
themselves, and proceed safely in completing their
tasks. Failure to comply with any of these requirements
could result in serious damage to the equipment and the
property in which it is situated, as well as severe personal
injury or death to themselves and people at the site.
This document is intended for use by owner-authorized
rigging, installation, and operating/service personnel. It
is expected that these individuals possess independent
training that will enable them to perform their assigned
tasks properly and safely. It is essential that, prior to
performing any task on this equipment, this individual
shall have read and understood the on-product labels,
this document and any referenced materials. This
individual shall also be familiar with and comply with
all applicable industry and governmental standards and
regulations pertaining to the task in question.
SAFETY SYMBOLS
The following symbols are used in this document to alert the reader to specific situations:
Indicates a possible hazardous situation
which will result in death or serious injury
if proper care is not taken.
Identifies a hazard which could lead to
damage to the machine, damage to other
equipment
and/or
environmental
pollution if proper care is not taken or
instructions and are not followed.
Indicates
a
potentially
hazardous
situation which will result in possible
injuries or damage to equipment if
proper care is not taken.
Highlights additional information useful
to the technician in completing the work
being performed properly.
External wiring, unless specified as an optional connection in the manufacturer’s product line, is not
to be connected inside the control cabinet. Devices such as relays, switches, transducers and controls
and any external wiring must not be installed inside the micro panel. All wiring must be in
accordance with Johnson Controls’ published specifications and must be performed only by a
qualified electrician. Johnson Controls will NOT be responsible for damage/problems resulting from
improper connections to the controls or application of improper control signals. Failure to follow
this warning will void the manufacturer’s warranty and cause serious damage to property or
personal injury.
This equipment is a relatively complicated apparatus.
During rigging, installation, operation, maintenance,
or service, individuals may be exposed to certain
components or conditions including, but not limited to:
heavy objects, refrigerants, materials under pressure,
rotating components, and both high and low voltage.
Each of these items has the potential, if misused or
handled improperly, to cause bodily injury or death. It is
the obligation and responsibility of rigging, installation,
and operating/service personnel to identify and recognize
these inherent hazards, protect themselves, and proceed
safely in completing their tasks. Failure to comply with
any of these requirements could result in serious damage
to the equipment and the property in which it is situated,
The following symbols are used in this document to alert the reader to specific situations:
Indicates a possible hazardous situation
which will result in death or serious injury
if proper care is not taken.
Indicates a potentially hazardous situation
which will result in possible injuries or
damage to equipment if proper care is not
taken.
External wiring, unless specified as an optional connection in the manufacturer’s product line, is not to
be connected inside the control cabinet. Devices such as relays, switches, transducers and controls and
any external wiring must not be installed inside the micro panel. All wiring must be in accordance with
Johnson Controls’ published specifications and must be performed only by a qualified electrician. Johnson
Controls will NOT be responsible for damage/problems resulting from improper connections to the controls
or application of improper control signals. Failure to follow this warning will void the manufacturer’s
warranty and cause serious damage to property or personal injury.
Identifies a hazard which could lead to
damage to the machine, damage to other
equipment and/or environmental pollution
if proper care is not taken or instructions
and are not followed.
Highlights additional information useful
to the technician in completing the work
being performed properly.
as well as severe personal injury or death to themselves
and people at the site.
This document is intended for use by owner-authorized
rigging, installation, and operating/service personnel. It
is expected that these individuals possess independent
training that will enable them to perform their assigned
tasks properly and safely. It is essential that, prior to
performing any task on this equipment, this individual
shall have read and understood the on-product labels, this
document and any referenced materials. This individual
shall also be familiar with and comply with all applicable
industry and governmental standards and regulations
pertaining to the task in question.
SAFETY SYMBOLS
Cooke Industries - Phone: +64 9 579 2185 Email: [email protected] Web: www.cookeindustries.co.nz
