background image

3. Drilling the holes and attaching the suspension bolts

If using anchor bolts

(1) Drill holes for anchor bolts at the locations at which you will set the suspension bolts. Note that anchor bolts must be

     obtained locally.

(2) Install the anchor bolts, then temporarily attach special nut "B" (included) and a locally-procured M10 nut to each of

     the bolts.

Anchor-bolt strength: 980 to 1470 N (100 TO 150 kgf)

4.Installing the indoor unit

(1) Lift unit so that suspension bolts pass through suspension fittings at

     the sides (four places),and slide the unit back.

(2) Fasten the indoor unit into place by tightening-up the special "B" bolts

     and the M10 nuts. Make sure that unit is secure and will not shift

    back and forth.

Ceiling panel

10 to 15 mm

Special nut A (included)

M10 nut (Obtained locally)

Special nut B (included)

(1) Drill   25mm holes at the suspension-bolt locations. The two special nuts are

     provided with the unit. The M10 nut must be obtained locally.

(2) Install the bolts, then temporarily attach Special nuts A and B and a normal

     M10 nut to each bolt.

Bolt strength: 980 to 1470 N (100 TO 150 kgf)

M10 Nut

(Obtaied locally)

Special nut B(included)

10 to 15 mm

M10 Nut (Obtaied locally)

5.Installing the coupler heat insulation

After checking for gas leaks, insulate by wrapping insulation around the two parts (large and small) of the indoor unit

coupling, using the coupler heat insulation. After installling the coupler heat insulation, wrap both ends with vinyl tape so

that there is no gap. Secure both ends of the heat insulation material using nylon fasteners.

Indoor unit

Nylon fastener (large)

Nylon fastener (small)

No gap

Coupler heat

insulation

Coupler heat insulation(large)

Coupler pipe (large)

Coupler pipe (small)

Coupler heat insulation(small)

Indoor unit

For half-concealed installation

In order to check the drainage, be sure to use a level during installation

of the indoor unit. If the installation site of the indoor unit is not level,

water leakage may occur.

CAUTION

Ceiling panel

Wall

When installing the indoor unit in a semi-concealed orientation, make

sure to reinforce the insulation of the unit on all sides. Drops of water

may fall from the unit if it is not thoroughly insulated.

Glass wool insulate

(10 to 20mm thick )

Indoor unit

(Top view)

Wall

Ceiling panel

Wall

Ceiling

When using an auxiliary pipe, make sure that the fastener used is insulated in the same way.

Note:

When installing the unit on the floor, fix the four rubber base feet in the accessories on the bottom plate of the unit with

four 4x16 screws and 4 flat washers, as the position in the figure.

A

The bottom plate of the unit.

4:1

A

rubber base foot

4x16 screw

flat washer

19

Installation Procedure

Summary of Contents for YHFMXH 028K BARX-FX





























Reviews: