background image

13

Installation and Maintenance

7.The Installation of the Outdoor Unit

Avoid

Direct sunlight 

Near Heat Source/ventilation fan  

Container With Flammable materials  

Thick Oil fog    

Wet Or Uneven place    

Aisle Or sideway  

7.1 Installation Sites

Place it in cool temperature.
Place it in an area with good ventilation.
Have required space for air inlet, outlet and 
maintenance. (Figure 7.1)
Make a strong base(10X40cm

2

 board made of 

concrete or similar). The appliance should be 
placed not less than 10 cm high to avoid being  
wet or corroded. Otherwise, it may cause  damage 
to the appliance or reduce its life time. (Figure 7.2)
Fix the base with hook bolts or alike to reduce 
vibration and noise. 

You should

If the total piping length is between 5m and 50m 
(Max. length), an additional refrigerant must be 
added. It's not necessary to add compressor oil.

Figure 7.3

Fig.7.3

7.2 Installation of the Outdoor Unit 

Firstly select the installation site and fix the outdoor 
unit. If it needs to be fixed onto the wall, make sure 
that the wall and the supporting rack is strong enough 
to hold the weight of the appliance.

Release the set screws of the electric cover, 
remove the electric cover (if the valve cover  is 
there either, please release it).          
Connect the indoor unit  wiring  to the outdoor unit 
panel according to the electric wiring diagrams. 
Be sure to make  each wire allowing 10cm longer 
than the required length for wiring.
Ground the unit following local electrical 
regulations.
Check the wiring with the wiring diagrams and 
make sure it's well connected. Fix the  wiring with 
clips and reinstall the electric cover.            

Wiring instruction for outdoor unit

Fig.7.4

Wire Ropes

in case a seasonal strong wind

 

blows against  the

unit

 .

Fix the unit with wire ropes to prevent overturning 

Top obstacle

Obstacle  

2m  

Air outlet  

2m  

Ground

Min.10cm

 Air inlet 

Min. 10cm

Min.

10cm  

Air outlet

Air inlet

Min.
35cm

Min.50cm

Fig. 7.1

Concrete base or similar

Min.10cm

Setscrew
(at least 4)

About 40cm

About 10cm

Fig.7.2

Tube length  L

Indoor unit

Height difference H

Outdoor unit

25(m)           10(m)

            15(g/m)          

25(m)           15(m)  

          15(g/m)          

30(m)           15(m)

            15(g/m)          

50(m)           30(m)

            35(g/m)          

Max. Tube 
length(L)     

Model   

9K   

18K

24K/36K/
42K/48K/
55K  

12K

Max. Height 
difference(H)

Add. 

Refrigerant

(exceed 5m)

Summary of Contents for YAKN09BZNWEUH1




















Reviews: