background image

5168274-BIM-I-1121

46

Johnson Controls Ducted Systems

HPS2

(left pin)

24 VAC hot return from refrigerant circuit 2 High 
Pressure Switch

Not effective for one stage compressor UCBs. Input is only 
considered if C2 output is needed; input must be present to 
allow C1 output. Three HPS2 trips in a two hour period cause a 
“High Pressure Switch 1 Lockout” and C2 output is then 
prevented until alarm reset. Connects through circuit trace to 
the right LPS2 pin.

LPS2

(right pin)

24 VAC hot out for refrigerant circuit 2 Low 
Pressure Switch

Not effective for one stage compressor UCBs. Connects 
through circuit trace to the left HSP2 pin

LPS2

(left pin)

24 VAC hot return from refrigerant circuit 2 Low 
Pressure Switch

Not effective for one stage compressor UCBs. Input is only 
considered after 30 seconds of C2 output; afterwards, input 
must be present to allow C2 output. Three LPS2 trips in a one 
hour period cause a “Low Pressure Switch 2 Lockout” and C2 
output is then prevented until alarm reset.

FAN OVR

(right pin)

24 VAC hot out for indoor blower FAN Overload 
relay contact/motor protector switch

Connects through circuit trace to the R terminal

FAN OVR

(left pin)

24 VAC hot return from indoor blower FAN 
Overload relay contact/motor protector switch

Input is only considered if FAN output is needed; input must be 
present to allow FAN output and unit operation. One FAN OVR 
trip lasting longer than 5 minutes or three FAN OVR trips in a 
two hour period cause a “Fan Overload Lockout” and unit 
operation is then prevented until alarm reset.

Terminal SA BUS

1

 connections on at left on lower edge and center of UCB

PWR

Power for SA (“Sensor-Actuator”) BUS devices

Also incorporated in the J8 6-pin phone jack connector at the 
left-center of the board. Posi- tive of the 15 VDC (reading to C) 
circuit for powering an optional netstat and/or MultiTouch 
gateway

C

Common for SA BUS power and communication 
circuits

Also incorporated in the J8 6-pin phone jack connector at the 
left-center of the board. Negative of the SA BUS circuits

Communication for SA BUS devices

Also incorporated in the J8 6-pin phone jack connector at the 
left-center of the board. Positive of the VDC (typically, a 
fluctuating 1.5 to 3.5 volts reading to C; at least 0.25 volts lower 
than +) SA BUS communication circuit to optional economizer 
board, 4-stage board, fault detection & diagnostics board, 
netstat and/or Multi Touch gateway

+

Communication for SA BUS devices

Also incorporated in the J8 6-pin phone jack connector at the 
left-center of the board. Positive of the VDC (typically, a 
fluctuating 1.5 to 3.5 volts reading to C; at least 0.25 volts 
higher than 

) SA BUS communication circuit to optional 

economizer board, 4-stage board, fault detection & diagnostics 
board, netstat and/or Multi Touch gateway

J8

6-pin phone jack connector

Incorporates the SA BUS terminals for convenience/alternate 
connection of SA BUS de- vices, primarily used for temporary 
service connection of the Multi Touch gateway

Item Integrated user interface at lower left corner of UCB

Display

On-board, 2-line x 8-character back-lit display

On-board display, buttons and joystick allow access to UCB, 
economizer, 4-stage and FDD board parameters

ENTER

Button for display menu acknowledgment and 
navigation

CANCEL

Button for display menu navigation and zeroing of 
active compressor ASCD timer

JOY

4-way Joystick for display menu navigation

Item USB connector at right of UCB

J10

Type A female Universal Serial Bus connector

Used for backup, restoration, & copying of board parameters as 
well as board software updating through a flash drive

Table 19: Smart Equipment™ UCB Details (Continued)

Description

Function & Comments

Summary of Contents for XA Series






















































Reviews: