FORM 100.50-NOM7 (808)
47
JOHNSON CONTROLS
4
Line 1 Display
Line 2 Display (Subgroup)
Configuration
1
- Config-General
2
- Config-Heat/Cool
3
- Config-Excess SAT
4
- Config-Econo/Exh
Changing setpoints is explained in the section titled
“PARAMETER DESCRIPTION AND OPTIONS”
under
“Changing Setpoints.” Changing a Configu
-
ration setpoint requires the entry of a password at the
appropriate level.
Line 3 will show the display item and Line 4 will display
of that item, such as “Setting = XXX”, where XXX is
the data. Information shown in Table 7 includes the text
for Line 3, units used with the associated item, default
value, value range, and the password level. A sample
display is shown above.
DISPLAY - SUBGROUP 2
Line 2 Heat/Cool System
Line 3 Freezestat
Line 4 Setting = OFF
“CONFIGURATION” NAVIGATION
The Configuration key (or Menu Item) will move the
display to the first item of the Configuration group. The
Configuration group of display items will allow the user
to view and change general unit Configuration data. Not
all Configuration parameters will be used for operation
based on how the unit is setup and configured. For ex
-
ample, IAQ Sensor Span will have a setting; however,
it will be ignored if the IAQ Sensor Enable Unit Setup
parameter is selected OFF.
Configuration parameters are listed in Table 21 with
their associated data, and explained under the section
titled “
PARAMETER DESCRIPTION AND OP-
TIONS (SETPOINTS)”.
As with the other function groups, the description of the
selected function,
** CONFIGURATION **
will be
displayed on line 1 of the display. Line 2 will display
one of the selected subgroups pertaining to the setpoint
being viewed/changed. The table below illustrates the
four subgroups under Configuration.
** CONFIGURATION **
Heat/Cool System
Freezestat
Setting = OFF
Pressing the Up and Down keys at this display item will
navigate the display cursor down and index the display
to show the additional days of the week. Pressing the
Change/Enter key at any of these days will prompt the
user for a password
(refer to section on Password).
Once
the password is entered, the start and stop times can be
changed by indexing the digits up and down with the
Up and Down keys, or moving between digits with the
Back or Next keys.
The Weekly Schedule sub menu will be as follows:
Weekly Schedule
Mon = HH:MM – HH:MM
Tue = HH:MM – HH:MM
Wed = HH:MM – HH:MM
Thu = HH:MM – HH:MM
Fri = HH:MM – HH:MM
Sat = HH:MM – HH:MM
Sun = HH:MM – HH:MM
Hol = HH:MM – HH:MM
Navigating to the Holiday Schedule display item will
show the following:
Pressing the Up and Down keys at this display item
will navigate the display cursor down and index the
display to show the additional holidays. Pressing the
Change/Enter key at any of these holidays will prompt
the user for a password. Once the password is entered,
the month (MMM) and day (DD) will be changeable
by pressing the Up and Down keys, or moving between
months and days with the Back or Next keys.
** HOLIDAY SCHEDULE **
↓
HOL 01= MMM DD
HOL 02= MMM DD
HOL 03= MMM DD
** HOLIDAY SCHEDULE **
↓
HOL 14= MMM DD
HOL 15= MMM DD
HOL 16= MMM DD
Pressing the DOWN key will index the bottom three
lines of text as shown.
Summary of Contents for J Series
