background image

P01432Q-rev.1 

25

(1)  Connect the cable for the optional controller or the optional extension cable to the terminals inside the 

electrical box through the connecting hole of the cabinet.

(2)  Connect the power supply and the ground wiring to the terminals in the electrical box.
(3)  Connect the cables between the indoor unit and the outdoor unit to the terminals inside the electrical box.
(4)  Connect cables to their corresponding terminal number and the similarly marked band.
(5)  Connect the communication cable between those indoor units connected to the same outdoor unit.
(6)  Do not connect the main power supply wiring to the communication line (Terminals A, B, 1 and 2 of 

TB2). If connected, the printed circuit board (PCB) will be destroyed.

(7)  Tightly clamp the power supply wiring and communication cables using the cable band inside the 

electrical box.

 

NOTE: 

When the standard wire is used for the field-wiring 

connection, the M4 crimping terminal should be used. 

When the single wire is used, fashion it into the shape 

as shown at right and connect it in order to tighten 

the washer uniformly. The screws at the terminal 

block should be tightened according to the torque 

specification as shown in the table above.

Stranded Wire

Single Wire

Connect it with

Crimping Terminal.

Connect it Direct

As Shown Below.

(8)  All electrical work should be performed in strict accordance with electrical schematics in the "Installation 

and Maintenance Manual".

(9)  If Power Supply Voltage (208V/230V) is introduced into the Communication Line: 

If 208V/230V are applied to the communication line at (Terminals 1 and 2 of TB2) by mistake, the fuse 

on the PCB for the communication line will blow. In this case, perform the recovery work as shown in 

the diagrams below.
 

(a)  Reconnect the wirings correctly.

 

(b)  Set the No.1 pin at DSW7 (on the PCB) to ON.

 

Upon PCB recovery after the fuse has been replaced, if 208V / 230V is reintroduced into the 

communication line, the PCB will be seriously damaged and will not recover.

L1

R

L2

AC 208V/230V

Incorrect Wiring

Reconnect wirings correctly.

5V

A B 1

2

S

L1

R

L2

AC 208V/230V

5V

A B 1

2

S

ON
OFF

DSW7

Set No.1 Pin

at ON side.

PCB

1 2

Summary of Contents for IDH072B21S Series













































Reviews: