York D12100 Manual Download

Page: 61 / 78

GLOBAL

INDUSTRIES, INC.

Drag Conveyors

10230011

2016-06-14

Intermediate Right Angle Rack and Pinion Gate Assembly

Assembly

Optional

Field cut and remove a 37 1/2” length segment

from the intermediate bottom as shown

(see

the example below)

. Center the cut between

36” [914 mm] bolt centers. Position and install

the gate to the conveyor along with the weather

cover and intermediate discharge hopper.

Electric rack and pinion gates are installed the

same way.

use 3/8” bolts

and flange nuts

NOTE: Bars on gates are made to be flush

with intermediate bottoms. Grind smooth any

unevenness.

ELECTRIC RACK AND PINION GATE

INTERMEDIATE SECTION

WEATHER

COVER

ROPE WHEEL

RACK AND PINION GATE

INTERMEDIATE DISCHARGE HOPPER

37 1/2” (+1/16” - 0) [953 mm]

caulk as needed

GRAIN FLOW

DIRECTION

towards

head

section

towards

tail

section

Summary of Contents for D12100















































































Search results

Summary of Contents for D12100

Reviews:

Related manuals for D12100

Brands by name

Popular brands

York D12100, Manual

Search results

Summary of Contents for D12100

Reviews:

Related manuals for D12100

Brands by name

Popular brands