YOKOGAWA Vnet/IP Technical Information Download Page 25

Page: 25 / 70

1. Overview of Vnet/IP

1-15

TI 30A10A05-01E

Connecting Vnet/IP domains with each other

Layer 3 switches connect Vnet/IP domains with each other. There can be up to 16 domains

connected in a system. Ensure that the communication bandwidth between domains is 1 Gbps

or more. To connect wide-area communication services in a narrow band network where the link

speed is less than 1 Gbps, contact YOKOGAWA.

The following figure shows the connection topology between domains. Layer 3 switches that are

installed for bus 1 and bus 2 connect the two Vnet/IP domains.

010403E.ai

FCS 0101

SCS 0102

L2SW

SCS 0202

FCS 0201

L2SW

L3SW

Vnet/IP Domain 1

Vnet/IP Domain 2

1Gbps

Information Network

Bus 1

SENG 0263

HIS 0264

HIS 0164

ENG 0163

SENG 0162

Figure Example of Connecting Vnet/IP Domains

Dec. 26, 2016-00

Summary of Contents for Vnet/IP







































































Search results

Summary of Contents for Vnet/IP

Reviews:

Related manuals for Vnet/IP

Brands by name

Popular brands

YOKOGAWA Vnet/IP, Technical Information

Search results

Summary of Contents for Vnet/IP

Reviews:

Related manuals for Vnet/IP

Brands by name

Popular brands