YOKOGAWA UTAdvanced UP55A, Technical Information

Page: 18 / 25

Output Setting
Menu Symbol Name Display level Setting range Initial value User setting
OUT OT Output type selection EASY
Control output or Heating-side control output (Lower two digits)
00: OFF
01: OUT terminals (voltage pulse)
02: OUT terminals (current)
03: OUT terminals (relay/triac)
04: OUT2 terminals (voltage pulse)
05: OUT2 terminals (current)
06: OUT2 terminals (relay/triac)
Cooling-side control output (Upper two digits)
00: OFF
01: OUT terminals (voltage pulse)
02: OUT terminals (current)
03: OUT terminals (relay/triac)
04: OUT2 terminals (voltage pulse)
05: OUT2 terminals (current)
06: OUT2 terminals (relay/triac)
Standard type: 00.03
Heating/cooling type: 06.03
CT
Control output cycle time
Heating-side control output cycle time (in
Heating/cooling control)
EASY 30.0 s
CTc Cooling-side control output cycle time EASY 30.0 s
V.AT Automatic valve position adjustment EASY
OFF: Stop automatic adjustment
ON: Start automatic adjustment
OFF
V.RS Valve position setting reset EASY
Setting V.RS to ON resets the valve adjustment settings and causes the
indication “V.RS” to blink.
OFF
V.L Fully-closed valve position setting EASY
Pressing the SET/ENTER key with valve position set to the fullyclosed position
by Down arrow key causes the adjusted value to be stored. When V.L
adjustment is complete, V.L stops blinking.
-
V.H Fully-open valve position setting EASY
Pressing the SET/ENTER key with valve position set to the fullyopened position
by Up arrow key causes the adjusted value to be stored. When V.H adjustment
is complete, V.H stops blinking.
-
TR.T Valve traveling time STD 5 to 300 s 60 s
V.MOD Valve adjusting mode STD
0: Valve position feedback type
1: Valve position feedback type
(moves to the estimating type if a feedback input error or break occurs.)
2: Valve position estimating type
0
RTS Retransmission output type of RET EASY
OFF: Disable
PV1: PV
SP1: SP
OUT1: OUT (Valve opening: 0 to 100 % in Position proportional control)
LPS: 15 V DC loop power supply
PV2: Loop-2 PV
SP2: Loop-2 SP
OUT2: Loop-2 OUT
TSP1: Target SP
HOUT1: Heating-side OUT
COUT1: Cooling-side OUT
MV1: Position proportional output internal computed value)
TSP2: Loop-2 target SP
HOUT2: Loop-2 heating-side OUT
COUT2: Loop-2 cooling-side OUT
MV2: Loop-2 position proportional output (internal computed value)
PV: PV terminals analog input
RSP: RSP terminals analog input
AIN2: AIN2 terminals analog input
AIN4: AIN4 terminals analog input
Loop-2 setting values are unavailable in Single-loop control.
PV1
RTH
Maximum value of retransmission output scale
of RET
STD 100 % of PV input range
RTL
Minimum value of retransmission output scale
of RET
STD 0 % of PV input range
O1RS
Retransmission output type of OUT current
output
STD Same as RTS OFF
O1RH
Maximum value of retransmission output scale
of OUT current output
STD -
O1RL
Minimum value of retransmission output scale
of OUT current output
STD -
O2RS
Retransmission output type of OUT2 current
output
STD Same as RTS OFF
O2RH
Maximum value of retransmission output scale
of OUT2 current output
STD -
O2RL
Minimum value of retransmission output scale
of OUT2 current output
STD -
OU.H 100% segmental point of OUT current output PRO 100.0%
OU.L 0% segmental point of OUT current output PRO 0.0%
OU2.H 100% segmental point of OUT2 current output PRO 100.0%
OU2.L 0% segmental point of OUT2 current output PRO 0.0%
RET.H 100% segmental point of RET current output PRO 100.0%
RET.L 0% segmental point of RET current output
PRO 0.0%
OU.A OUT current output range STD 4-20
OU2.A OUT2 current output range STD 4-20
RET.A RET current output range STD 4-20
Heater Break Alarm Setting
Menu Symbol Name Display level Setting range Initial value User setting
HBA HB1.S Heater break alarm-1 function selection EASY 1
HB2.S Heater break alarm-2 function selection EASY 1
HB1 Heater break alarm-1 current setpoint EASY OFF
HB2 Heater break alarm-2 current setpoint EASY OFF
CT1.T CT1 coil winding number ratio EASY 800
CT2.T CT2 coil winding number ratio EASY 800
HDN1 Heater break alarm-1 Ondelay timer STD 0.00
HDN2 Heater break alarm-2 Ondelay timer STD 0.00
HDF1 Heater break alarm-1 Offdelay timer PRO 0.00
HDF2 Heater break alarm-2 Offdelay timer PRO 0.00
HB1.D Heater break alarm-1 contact type PRO CLS
HB2.D Heater break alarm-2 contact type PRO CLS
RS-485 Communication Setting
(E3 terminal
area)
(E4 terminal
area)
Menu Symbol Name Display level Setting range Initial value User setting User setting
R485 PSL Protocol selection EASY
PCL: PC link communication
PCLSM: PC link communication (with checksum)
LADR: Ladder communication
CO-M: Coordinated master station
MBASC: Modbus (ASCII)
MBRTU: Modbus (RTU)
CO-S2: Coordinated slave station (Loop-2 mode)
P-P: Peer-to-peer communication
MBRTU
BPS Baud rate EASY
600: 600 bps
1200: 1200 bps
2400: 2400 bps
4800: 4800 bps
9600: 9600 bps
19200: 19.2k bps
38400: 38.4k bps (except for communication of E4 terminal area)
19200
PRI Parity EASY
NONE: None
EVEN: Even
ODD: Odd
EVEN
STP Stop bit EASY 1: 1 bit, 2: 2 bits 1
DLN Data length EASY 7: 7 bits, 8: 8 bits 8
ADR Address EASY 1 to 99 1
RP.T Minimum response time PRO 0 to 10 (x10ms) 0
0.5 to 1000.0 s
When RTS = PV1, SP1, PV2, SP2, TSP1, TSP2, PV, RSP, AIN2, or AIN4,
RTL + 1 digit to 30000
-19999 to RTH - 1 digit
Decimal point position:
When RTS=PV1, SP1, or TSP1, decimal point position is same as that of PV
input.
When RTS=PV2, SP2, or TSP2, decimal point position is same as that of RSP
input.
When RTS=PV, decimal point position is same as that of PV input scale.
When RTS=RSP, decimal point position is same as that of RSP input scale.
When RTS=AIN2, decimal point position is same as that of AIN2 scale.
When RTS=AIN4, decimal point position is same as that of AIN4 scale.
When O1RS = PV1, SP1, PV2, SP2, TSP1, TSP2, PV, RSP, AIN2, or AIN4,
O1RL + 1 digit to 30000
-19999 to O1RH - 1 digit
Decimal point position:
When O1RS=PV1, SP1, or TSP1, decimal point position is same as that of PV
input.
When O1RS =PV2, SP2, or TSP2, decimal point position is same as that of RSP
input.
When O1RS =PV, decimal point position is same as that of PV input scale.
When O1RS =RSP, decimal point position is same as that of RSP input scale.
When O1RS =AIN2, decimal point position is same as that of AIN2 scale.
When O1RS =AIN4, decimal point position is same as that of AIN4 scale.
When O2RS = PV1, SP1, PV2, SP2, TSP1, TSP2, PV, RSP, AIN2, or AIN4,
O2RL + 1 digit to 30000
-19999 to O2RH - 1 digit
Decimal point position:
When O2RS=PV1, SP1, or TSP1, decimal point position is same as that of PV
input.
When O2RS =PV2, SP2, or TSP2, decimal point position is same as that of RSP
input.
When O2RS =PV, decimal point position is same as that of PV input scale.
When O2RS =RSP, decimal point position is same as that of RSP input scale.
When O2RS =AIN2, decimal point position is same as that of AIN2 scale.
When O2RS =AIN4, decimal point position is same as that of AIN4 scale.
-100.0 to 200.0%
4-20: 4 to 20 mA
0-20: 0 to 20 mA
20-4: 20 to 4 mA
20-0: 20 to 0 mA
0: Heater current measurement
1: Heater break alarm
OFF, 0.1 to 300.0 Arms
1 to 3300
0.00 to 99.59 (minute.second)
CLS: When the event occurs, the contact is closed.
OPN: When the event occurs, the contact is opened.
Page 18 / 25