background image

To hold the gate open for easy walking through:

!

WARNING

Gate in closed position

Swing to the open positions

1

2

Troubleshooting

If the gate does not stay closed:
1.Upper latch set is too close to the corner where the locking housing is located.
Solution: Adjust the upper tension knobs by turning them outward, so that there is a proper distance between the upper latch set
and the corner. Make sure the upper latch set still stays below the release button as illustration 6B.

2. Lower latch set position is too low.
Solution: Adjust the upper tension knob on the side of locking housing corner by turning it inward, meanwhile turning the other
upper tension knob outward, until the upper latch set and the corner are in the right position. Make sure the upper latch set is
still below the release button as illustration 6B.

If the gate does not stay in position:
Gate may not install properly as step3 (3A ,3B), remove and reinstall the gate, make sure the gate is installed vertically.

CARE:

CLEANING: Clean the safety gate by using warm water and a mild detergent. Use a soft cloth or sponge to avoid
scratches. Never use solvents or chemicals to clean the safety gate.
ATTENTON:
1.Do not use the product if any components are broken or missing. Do not use replacement parts other than those
approved by the manufacturer or distributor. Non approved spare parts may render the repair or the product unsafe.
2.Check regularly that all fittings and components are secure and that no components are worn, broken or missing.
3.Check regularly that all fittings are securely tightened and that the locking mechanism is working properly.

DEMBY DEVELOPMENT CO.,LTD.

10F.,NO. 29-5, SEC.2, ZHONGZHENG E.RD., DANSHUI DIST., NEW TAIPEI CITY 251, TAIWAN, R.O.C.

Tel:886-2-88091866

Top view

The hold-gate-open system can be used by adults only. Once the gate is held open, the
automatic closing feature of the gate will not work anymore, so your child could move back and
forth without restriction. Swing the gate to the open positions to hold the gate open for easy
walking through. (Fig.1 / Fig.2)

!

WARNING

Indicator of locking system

The Warning sign will appear green color when gate is locked properly.

The Warning sign will appear red color if the gate is opened or not locked properly.
Please notice and re-lock the gate.

Red

Green

ENGLISH

Summary of Contents for Y1













Reviews: