Yetter 5000 SERIES Owner'S Manual & Parts List Download Page 29

Page: 29 / 32

TROUBLSHOOTING

ISSUE

CAUSE

CORRECTIVE ACTION

Residue Plugging

or wrapping

1. Incorrect Head Angle
2. Roller Mount Tube

incorrectly installed

3. Pivot arm orientation

incorrect

4. Bearing installed

incorrectly

5. Devastator bottomed out

1. Adjust head angle to 23

– 25 degrees (

see page 15)

2. Make sure the Bearing Support Tab is on the backside

of the Roller Arm Mount Tube

3. Reposition the pivot arm so that it offsets under the

snout & not under the row

4. Make sure the side of the bearing that protrudes

outside of the cast housing is facing toward the roller
(each roller should spin freely by hand)

5. Raise head to allow travel, make sure angle is correct

Stalk are

n’t

“devastated”

1. Operating corn head too

high

1. Lower corn head until the rollers engage

Corn Head won’t

fit on head cart

1.   Devastators bottom out
2.   Roller won’t clear cart tire
3.   Storage stands don’t rest
      in the saddles on the cart

1.  Adjust top rail & saddles higher on cart
2.  Use side tilt to clear tires (if using a dual rear axle cart)
3.  Order 5000-081 Head Extensions (JD 600 & 700 series
     only)

Summary of Contents for 5000 SERIES

































Search results

Summary of Contents for 5000 SERIES

Reviews:

Related manuals for 5000 SERIES

Brands by name

Popular brands

Yetter 5000 SERIES, Owner'S Manual & Parts List

Search results

Summary of Contents for 5000 SERIES

Reviews:

Related manuals for 5000 SERIES

Brands by name

Popular brands