Yetter 5000 SERIES Owner'S Manual & Parts List Download Page 8 | Manualshive

Page: 8 / 32

background image

8

5000-071 ASSEMBLY INSTRUCTIONS

LEXION

– CAPELLO

NOTE:

SUPPORT THE FRONT OF THE ROW UNIT BEFORE LOOSENING ANY MOUNTING HARDWARE.

DIFFERENT MOUNT LOCATIONS MAY BE NECESSARY IF CLEARANCE ISSUES ARE FOUND.

Step 1

: Remove the mounting hardware & strap for each gear box where the Yetter torsion pivot assembly will

be mounted (see torsion pivot locations on pages 10

– 11 that match your devastator kit). Install the 5000-452

Lexion adaptor bracket on the bottom side of the frame using 4) 2502-813 M16 X 2 X 70 8.8 bolts, the original flat
washers & spacer bushing. Thread bolts by hand, then tighten to torque spec. (4

th

bolt not shown in photo)

Step 2

: Place the 5000-167 torsion pivot assembly on the 5000-285 adaptor aligning all 4 holes. Thread the

2502-810 M16 X 2 X 30 bolts by hand, and then tighten to torque spec.

Step 3

: Refer to page 13 for instructions on installing the 5000-292 torsion arm.

«
...
6
7
8
9
10
...
»

Summary of Contents for 5000 SERIES

































Reviews:

No comments

Related manuals for 5000 SERIES

Brand: ACS Pages: 56

Brand: Odom Pages: 19

Brand: MacDon Pages: 30

Brand: Malmet Pages: 14

Brand: Zempire Pages: 2

Brand: Gaspardo Pages: 16

Brand: Gastrodomus Pages: 4

Brand: HANYOUNG NUX Pages: 2

Brand: Gastrodomus Pages: 39

Brand: IBEX Pages: 4

Brand: IDEAL Pages: 12

Brand: Kärcher Pages: 88

TRAKTOR KONTROL S4

Brand: Native Instruments Pages: 86

Brand: Native Instruments Pages: 245

Brand: Rational Pages: 16

Brand: Yamaha Pages: 48

Brand: Yamaha Pages: 85

Brand: Yamaha Pages: 43

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands