manualshive.com logo in svg

YASKAWA VS MINI J7 series, Instruction Manual, Page: 9 / 118

Share
Download
YASKAWA VS MINI J7 series Instruction Manual Download Page 9

9

MAINTENANCE AND INSPECTION

CAUTION

(Ref. page)

• Never touch the heatsink or braking resistor, the 

temperature is very high.

Failure to observe this caution can result in harmful burns 
to the body.

• Since it is easy to change operation speed from low to 

high speed, verify the safe working range of the motor 
and machine before operation.

Failure to observe this caution can result in personal injury 
and machine damage.

• Install a holding brake separately if necessary.

Failure to observe this caution can result in personal injury.

• Do not change signals during operation.

The machine or the inverter may be damaged.

• All the parameters of the inverter have been preset at 

the factory. Do not change the settings unnecessarily.

The inverter may be damaged. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  25

WARNING

(Ref. page)

• Never touch high-voltage terminals in the inverter.

Failure to observe this warning can result in an electrical shock.  . . . . . . . . . .  99

• Disconnect all power before performing maintenance or 

inspection. Then wait at least one minute after the power 
supply is disconnected and all LEDs and CHARGE LED 
are extinguished.

The capacitors discharge slowly, and may be dangerous. . . . . . . . . . . . . . . . .  99

All manuals and user guides at all-guides.com

Summary of Contents for VS MINI J7 series























































































































Reviews:

No comments