manualshive.com logo in svg

YASKAWA VS MINI J7 series, Instruction Manual, Page: 111 / 118

Share
Download
YASKAWA VS MINI J7 series Instruction Manual Download Page 111

111

Appendix - CE Conformance

CE     Conformance - Low Voltage Directive (LVD) Compliance

                           

                                           

•

These circuits are hazardous and are separated from accessibility by protective 

separation.

‚

These circuits are not separated from hazardous circuits by protective 

separation, but only with basic insulation.  These circuits cannot be accessed and 
must not be interconnected with any circuits which are accessible, unless they 
are isolated from accessible circuits by supplemental insulation.  These circuits 
can be connected only to the following circuits:

30VDC or less (overvoltage category 2)

250 VAC or less (overvoltage category 2)

ƒ

These circuits are not separated from hazardous circuits by protective 

separation, but only with basic insulation.  These circuits cannot be accessed and 
must not be interconnected with any circuits which are accessible, unless they 
are isolated from accessible circuits by supplemental insulation.  

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for VS MINI J7 series























































































































Reviews:

No comments