manualshive.com logo in svg

YASKAWA SI-EP3/V, Technical Manual

Share
Download
YASKAWA SI-EP3/V Technical Manual Download Page 8

2  Product Overview

YASKAWA

 SIEP YEACOM 06 V1000 Option PROFINET SI-EP3/V  Technical Manual

 8

2

Product Overview

‹

About This Product

The SI-EP3/V option connects the V1000 drive to a PROFINET network and facilitates the exchange of data.

This manual explains the handling, installation and specifications of this product.

The SI-EP3/V option is a simple, networking solution that reduces the cost and time to wire and install factory automation 
devices, while providing interchangeability of like components from multiple vendors.

By installing the option to a drive, it is possible to do the following from a PROFINET master device:

• Operate the drive
• Monitor the operation status of the drive
• Change parameter settings.

SI-EP3/V is PROFINET Conformance Class A certified.

‹

Applicable Models

This option can be used with the drive models in 

Table 1

.

Table 1  Applicable Models

Drive

Software Version

<1>

<1> See “PRG” on the drive nameplate for the software version number.

CIMR-V

……

A

……………

A

…

≥

 

1012

Summary of Contents for SI-EP3/V






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands