manualshive.com logo in svg

YASKAWA SI-EP3/V, Technical Manual

Share
Download
YASKAWA SI-EP3/V Technical Manual Download Page 25

7  PROFINET Messaging

25

 

YASKAWA

 SIEP YEACOM 06 V1000 Option PROFINET SI-EP3/V  Technical Manual

Table 9  Status Word for the PROFIdrive Communication Profile

Bit

Name

Value

STATE/Description

0 RDY_ON 

1 

READY TO SWITCH ON. 

0 

NOT READY TO SWITCH ON. 

1 RDY_RUN 

1 READY 

TO 

OPERATE. 

0 OFF1 

ACTIVE. 

2 RDY_REF 

1 ENABLE 

OPERATION. 

0 DISABLE 

OPERATION. 

3 TRIPPED 

1 FAULT. 
0 No 

fault. 

4 OFF_2_STA 

1 OFF2 

inactive. 

0 OFF2 

ACTIVE. 

5 OFF_3_STA 

1 OFF3 

inactive. 

0 OFF3 

ACTIVE. 

6 SWC_ON_INHIB 

1 SWITCH-ON 

INHIBIT 

ACTIVE. 

0 

SWITCH-ON INHIBIT NOT ACTIVE. 

7 ALARM 

1 Warning/Alarm. 
0 No 

Warning/Alarm. 

8

AT_SETPOINT 

1 

OPERATING. Actual value equals reference value (i.e., is within tolerance limits). 

0 

Actual value differs from reference value (i.e., is outside tolerance limits). 

9 REMOTE 

1 

Drive control location: REMOTE. 

0 

Drive control location: LOCAL. 

10 ABOVE_LIMIT 

-

Not 

supported. 

11 to 15

-

-

Reserved 

Summary of Contents for SI-EP3/V






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands