manualshive.com logo in svg

YASKAWA SI-EP3/V, Technical Manual

Share
Download
YASKAWA SI-EP3/V Technical Manual Download Page 17

5  Installation Procedure

17

 

YASKAWA

 SIEP YEACOM 06 V1000 Option PROFINET SI-EP3/V  Technical Manual

8.

On NEMA Type 1 enclosure drives, the screw for the drive ground terminal also acts as one of the screws that 
attaches the NEMA Type 1 conduit bracket to the drive. Reattach the NEMA Type 1 conduit bracket according to 

Figure 11

 and connect the drive-side of the ground wire to the drive ground terminal. 

Note:

The four different ground wires packaged with the option connect the option to different drive models. Select the proper ground 
wire depending on drive size.

Figure 11  

Figure 11  Reattach the NEMA Type 1 Conduit Bracket and Connect the Ground Wire

9.

Reattach the bottom cover. Keep the ground wire inside of the bottom cover when reattaching.

Figure 12  

Figure 12  Reattach the Bottom Cover

10.

On models CIMR-V

…

BA0006

…

 to BA0018

…

, 2A0010

…

 to 2A0069

…

, and 4A0001

…

 to 4A0038

…

, reattach the 

terminal cover.
Refer to 

Figure 14

 for drive models CIMR-V¨BA0006

…

 to BA0018

…

, 2A0010

…

 to 2A0020

…

, and 4A0001

…

 to 

4A0011

…

, which require routing the ground wire through the provided notch when reinstalling the terminal cover.

Ground terminal

Ground wire

Drive ground terminal/
NEMA Type 1 conduit 
bracket screw

Ground wire

Drive-side 
connector
Screw size:
M3.5 to M6

Option unit 
connector
Screw size: M3

IP20/Open-Chassis                                     IP20/NEMA Type 1 Enclosure

Summary of Contents for SI-EP3/V






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands