manualshive.com logo in svg

YASKAWA SI-EP3/V, Technical Manual

Share
Download
YASKAWA SI-EP3/V Technical Manual Download Page 20

5  Installation Procedure

YASKAWA

 SIEP YEACOM 06 V1000 Option PROFINET SI-EP3/V  Technical Manual

 20

„

Communication Cable Wiring

The dual RJ45 network ports on the option board act as a switch to allow for flexibility in cabling topology. For example, 
a traditional star network topology may be employed by using a single port on the option board. Alternatively, a daisy-
chained approach may be employed by using both RJ45 ports. This second approach reduces the requirements of central 
switch ports.

Figure 19  

Figure 19  Topology Options

Communication Cable Specifications

Only use cables recommended for PROFINET. Using a cable not specifically recommended may cause the option or 
drive to malfunction.

The use of CAT5e or equivalent Shielded Twisted Pair (STP) cable is recommended.

15.

Use the second communication cable port to daisy chain a series of drives where applicable.

„

Connection Diagram

Figure 20  

Figure 20  Wiring Diagram

<1> The ground wire provided in the option shipping package must be connected during installation.

STOP

(Hz)

(Hz)
(A)
(V)

V1000

STOP

(Hz)

(Hz)
(A)
(V)

V1000

STOP

(Hz)

(Hz)
(A)
(V)

V1000

STOP

(Hz)

(Hz)
(A)
(V)

V1000

STOP

(Hz)

(Hz)
(A)
(V)

V1000

STOP

(Hz)

(Hz)
(A)
(V)

V1000

V1000

M

U/T1
V/T2

W/T3

R/L1
S/L2

T/L3

SI-EP3/V

PROFINET 

 Option

FE

<1>

PROFINET Master

PROFINET Cable

Motor

Power

PROFINET Cable

Summary of Contents for SI-EP3/V






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands