YASKAWA CIMR-F7Z, Instruction Manual

Page: 64 / 67

61
Appendix-4: Parameter Table [continued]
No. Parameter Name
Initial
Value
Setting
Value
No. Parameter Name
Initial
Value
Setting
Value
E3-05
Motor 2 Mid Output Frequency (FB)
(Mid Frequency) 3.0
*1
F1-10
Excessive Speed Deviation Detection Level
(PG Deviate Level)
10
E3-06
Motor 2 Mid Output Frequency Voltage (VC)
(Mid Voltage) 12.0
*1 *3
F1-11
Excessive Speed Deviation Detection Time
(PG Deviate Time)
0.5
E3-07
Motor 2 Min . Output Frequency (FMIN)
(Min frequency) 0.5
*1
F1-12
Number of PG Gear Teeth 1
(PG # Gear Teeth 1)
0
E3-08
Motor 2 Min . Output Frequency Voltage
(VMIN)
(Min Voltage)
2.0
*1 *3
F1-13
Number of PG Gear Teeth 2
(PG # Gear Teeth 2)
0
E4-01
Motor 2 Rated Current
(Motor Rated FLA) 1.90
*2
F1-14
PG Open-Circuit Detection Time
(PGO Detection Time)
2.0
E4-02
Motor 2 Rated Slip
(Motor Rated Slip) 2.90
*2
F2-01
Bi-polar or Uni-polar Input selection
(AI-14 Input Sel)
0
E4-03
Motor 2 No-Load Current
(No-Load Current) 1.20
*2
F3-01
Digital Input Option
(DI Input)
0
E4-04
Motor 2 Number of Poles
(Number of Poles)
4 F6-01
Operation Selection after Communication Error
(BUS Fault Sel)
1
E4-05
Motor 2 Line-to-Line Resistance
(Term Resistance) 9.842
*2
F6-02
Input Level of External Fault from
Communications Option Card
(EF0 Detection)
0
E4-06
Motor 2 Leak Inductance
(Motor 2 Leak) 18.2
*2
F6-03
Stopping Method for External Fault
from Communication Option Card
(EF0 Fault Action)
1
E4-07
Motor 2 Rated Capacity
(Mtr Rated Power) 0.40
*2
F6-04
Trace Sampling from Communications
Option Card
(Trace Sample Tim)
0
F1-01
PG Constants
(PG Pulses/Rev)
600 F6-06
Torque Reference/Torque Limit
Selection from Optical Option
(Torq Ref/Lmt Sel)
1
F1-02
Operation Selection at PG Open Circuit (PGO)
(PG Fdbk Loss Sel)
1 H1-01
Terminal S3 Function Selection
(Terminal S3 Sel)
24
F1-03
Operation Selection at Overspeed (OS)
(PG Overspeed sel)
1 H1-02
Terminal S4 Function Selection
(Terminal S4 Sel)
14
F1-04
Operation Selection at Deviation
(PG Deviation Sel)
3 H1-03
Terminal S5 Function Selection
(Terminal S5 Sel)
0
F1-05
PG Rotation
(PG Rotation Sel)
0 H1-04
Terminal S6 Function Selection
(Terminal S6 Sel)
3
F1-06
PG Division Rate (PG Pulse Monitor)
(PG Output Ratio)
1 H1-05
Terminal S7 Function Selection
(Terminal S7 Sel)
9
F1-07
Integral Value During Accel/Decel
Enable/Disable
(PG Ramp PI/I Sel)
0 H2-01
Terminal M1-M2 Function Selection
(Contact)
(Term M1-M2 Sel)
21
F1-08
Overspeed Detection Level
(PG Overspd Level)
115
H2-02
Terminal P1 Function Selection
(Term P1 Sel)
1
F1-09
Overspeed Detection Delay Time
(PG Oversp eed Time) 0.0
*1
H2-03
Terminal P2 Function Selection
(Term P2 Sel)
2
*1 Factory/default settings will vary based on Control Mode (A1-02), or by the value set to parameter E3-01.
*2 Both the setting range and factory/default settings will vary based on drive capacity.
*3 Values shown here are for 200V class drives. Double values when working with 400V class drives.