Yardistry YM12784 Installation And Operating Instructions Manual Download

Page: 50 / 84

[email protected]

Hardware

Wood Parts

F18.6

24 x #8 x 2-1/4” Wood Screw
12 x #8 x 2-1/2” Wood Screw

12 x (633) Centre Rafter

Flush

#8 x 2-1/2”

Wood Screws

#8 x 2-1/4”

Wood Screws

Step 18: Large Roof Assembly

Part 2

F18.5

(633) Centre

Rafter

Note notches

facing up

Flush

F18.7

Place three (633) Centre Rafters over the pilot holes in (1192) Mid Fascia and (1194) Rafter Top so they are

flush to the top of each board, as shown in F18.5. Make sure (633) Centre Rafters are square to (1192) Mid

Fascia and (1194) Rafter Top then attach (1194) Rafter Top to rafters with two #8 x 2-1/4” Wood Screws per

rafter and (1192) Mid Fascia to rafters with one #8 x 2-1/2” Wood Screw per rafter. Repeat for each Large Roof

Assembly. (F18.5, F18.6 and F18.7)

(633) Centre

Rafter

Flush

#8 x 2-1/2”

Wood Screws

(1192) Mid

Fascia

(1192) Mid

Fascia

(675)

Middle

Rafter

(675)

Middle

Rafter

(633) Centre

Rafter

(1194)

Rafter Top

(1194)

Rafter Top

Summary of Contents for YM12784





















































































Search results

Summary of Contents for YM12784

Reviews:

Related manuals for YM12784

Brands by name

Popular brands

Yardistry YM12784, Installation And Operating Instructions Manual

Search results

Summary of Contents for YM12784

Reviews:

Related manuals for YM12784

Brands by name

Popular brands