Yardistry YM12784 Installation And Operating Instructions Manual Download

Page: 32 / 84

[email protected]

F8.9

Step 8: Small Roof Assembly

Part 3

F8.10

Hardware

Wood Parts

#8 x 1-1/2” Wood Screws

x 4 per board

32 x #8 x 1-1/2” Wood Screw

2 x (636) Top Strap
2 x (637) Mid Strap
2 x (687) Bottom Strap LT
2 x (688) Bottom Strap RT

(637) Mid

Strap

Overhang

(624) Rafter

Corner Left

(623) Rafter

Corner Right

(636) Top

Strap

(687) Bottom

Strap LT

#8 x -1-1/2”

Wood Screws

Place one (636) Top Strap, one (637) Mid Strap, one (687) Bottom Strap LT and one (688) Bottom Strap

RT in the notches of each rafter so the ends do not overhang the outside edges of the outside boards. (687)

Bottom Strap LT and (688) Bottom Strap RT sit tight together. Attach with four #8 x 1-1/2” Wood Screws per

strap. Complete for each Small Roof Assembly. (F8.9, F8.10 and F8.11)

(637) Mid

Strap

(636) Top

Strap

(687) Bottom

Strap LT

Overhang

(688) Bottom

Strap RT

Notice these

screws go in

at an angle

F8.11

Summary of Contents for YM12784





















































































Search results

Summary of Contents for YM12784

Reviews:

Related manuals for YM12784

Brands by name

Popular brands

Yardistry YM12784, Installation And Operating Instructions Manual

Search results

Summary of Contents for YM12784

Reviews:

Related manuals for YM12784

Brands by name

Popular brands