Yardistry YM12784 Installation And Operating Instructions Manual Download

Page: 48 / 84

[email protected]

(2)Roof Ridge Left -Y010XX-134

#7 x 18mm W.S x9

(2)Roof Ridge Right -Y010XX-135

Assembly x2

1inch from panel top to Y010XX-209 Ridge Clip

74.8 - Up 2¼ inch from bottom rafter

(2)Roof Ridge Left -Y010XX-134

#7 x 18mm W.S x9

(2)Roof Ridge Right -Y010XX-135

Assembly x2

1inch from panel top to Y010XX-209 Ridge Clip

74.8 - Up 2¼ inch from bottom rafter

(2)Roof Ridge Left -Y010XX-134

#7 x 18mm W.S x9

(2)Roof Ridge Right -Y010XX-135

Assembly x2

1inch from panel top to Y010XX-209 Ridge Clip

74.8 - Up 2¼ inch from bottom rafter

(2)Roof Ridge Left -Y010XX-134

#7 x 18mm W.S x9

(2)Roof Ridge Right -Y010XX-135

Assembly x2

1inch from panel top to Y010XX-209 Ridge Clip

74.8 - Up 2¼ inch from bottom rafter

(2)Roof Ridge Left -Y010XX-134

#7 x 18mm W.S x9

(2)Roof Ridge Right -Y010XX-135

Assembly x2

1inch from panel top to Y010XX-209 Ridge Clip

74.8 - Up 2¼ inch from bottom rafter

8x #7 x 18 mm Wood Screw

2 x Roof Edge Left 72.2 2 x Roof Edge Right 72.2

Step 17: Attach Ridge Clips - Corner Roof Assemblies

Hardware

F17.1

36 x #7 x 3/4” Wood Screw

Place one Weather Seal on the inside of four Ridge Clip 102.5 then place one Ridge Clip 102.5 on each (623)

Rafter Corner Right and each (624) Rafter Corner Left so they cover the panels and are flush to the top, then attach

with five #7 x 3/4” Wood Screws per Ridge Clip 102.5. Bottom edge of Ridge Clip 102.5 should be 2-3/4” (6.985

cm) up from the bottom edge of Rafter Corners Left and Right. (F17.1, F17.2, F17.3 and F17.4)

Place one Weather Seal 75-1/2 on the inside of four Ridge Clip 73.5 then place one Ridge Clip 73.5 on each

(675) Middle Rafter on both Left and Right Corner Roof Assemblies so they cover the panels and attach with four

#7 x 3/4” Wood Screws per Ridge Clip 73.5. The top of each Ridge Clip 73.5 should be 1”(2.54 cm) from the tip of

(675) Rafter Middle and bottom edge should be 2-1/4” (5.72 cm) up from the bottom edge of (675) Middle Rafter.

(F17.1, F17.2, F17.3, F17.5 and F17.6)

Weather Seal /

Weather Seal 75-1/2

F17.6

#7 x 3/4”

Wood Screws

Panels

Components

4 x Ridge Clip 102.5
4 x Ridge Clip 73.5
4 x Weather Seal
4 x Weather Seal 75-1/2

F17.3

Underneath,

Side View

F17.5

Side View

#7 x 3/4” Wood

Screws

Ridge Clip

102.5 / 73.5

Ridge Clip

102.5

Ridge Clip

102.5

Ridge

Clip

73.5

Left Corner

Roof Assembly

Right Corner

Roof Assembly

Top

F17.4

F17.2

Top

Ridge Clip

102.5

Weather

Seal 75-1/2

Weather

Seal

Rafter Corner

(Left/Right)

Panels

(675) Middle

Rafter

(675) Middle

Rafter

2-1/4”

1”

Top

Flush

Ridge

Clip

73.5

Ridge Clip

73.5

Ridge

Clip

73.5

2-3/4”

5.72 cm

2.54 cm

6.985 cm

Summary of Contents for YM12784





















































































Search results

Summary of Contents for YM12784

Reviews:

Related manuals for YM12784

Brands by name

Popular brands

Yardistry YM12784, Installation And Operating Instructions Manual

Search results

Summary of Contents for YM12784

Reviews:

Related manuals for YM12784

Brands by name

Popular brands