16
17
NOTE:
Sharp blades will greatly enhance the
performance of the reel mower, especially
when cutting tall grass.
• When cutting thick grass, reduce your
walking speed in order to allow for a more
effective cut and a proper discharge of the
clippings. For a healthy lawn, always cut
off one-third or less from the total length
of the grass. The average lawn should be
approximately 1.5 in. to 2 in. (3.8 cm to 5 cm)
long during cool months, and more than 2
in. (5 cm) long during hot months. If there is
growth, the lawn should be cut in the fall.
• The lawn will look better if it is always cut to
the same height and in alternate directions.
• When crossing any gravelled surfaces,
release the On/Off switch bail to turn off the
mower. The stones can be picked up and
thrown by the rotating blade.
• Set the mower to the highest cutting height
when mowing on uneven ground or in tall
weeds.
WARNING!
If you strike a foreign object,
stop the motor and remove the battery.
Thoroughly inspect the mower and repair
any damage before resuming work.
• Switch off the motor before emptying the
grass collection bag. Always ensure that a
safe distance (provided by the length of the
long handles) is maintained between the user
and the mower housing. Be especially careful
when mowing and changing direction on
slopes and inclines.
• Maintain a solid footing and wear sturdy, non-
slip footwear and long trousers. Always mow
across an incline (not up and down).
• Use special caution when backing up and
pulling the reel mower towards you as such
maneuvering of the machine poses a tripping
hazard.
• For effective mulching, do not cut wet grass;
it tends to stick to the underside of the deck,
preventing the proper mulching of grass
clippings. The best time to mow grass is in
the late afternoon, when the grass is dry and
the newly cut area will not be exposed to
direct sunlight.
• For the best mulching performance, set
the cutting height to remove approximately
one third of the grass length, ideally no
more than 1.5 in. at one time. If the grass is
overgrown, it may be necessary to increase
the cut height to make it easier to mow and
to prevent overloading the motor. Slow your
cutting pace in tall or thick grass conditions.
For mulching extremely thick or tall grass, it
is advisable to first cut at a high cut-height
setting, and then re-cut to the final cut height.
Otherwise, make narrower cuts and mow
slowly. ALWAYS MAKE SURE THAT THE
BLADE IS SHARP.
MAINTENANCE
WARNING!
Before cleaning, repairing,
or inspecting the reel mower, stop the
machine, disconnect the safety key and the
battery. Verify that all moving parts have
come to a complete stop.
General
• Always keep the reel mower clean and free
of grass, dirt, or other debris.
• Keep the handles dry, clean, and free of oil
and grease.
• After each cutting session, remove
accumulated grass clippings and debris using
either a dry cloth or hand brush. You may
also clean the equipment with a damp cloth.
Do not use cleaning agents or harsh solvents
as they may damage the equipment's plastic
components. Make sure that no water
penetrates the equipment's interior as intake
of water can destroy the switch mechanism
and the electric motor.
• Do not clean the reel mower with running
water, particularly with high-pressure water.
• Check all nuts, bolts, and screws for proper
tightness before each use.
• Frequently inspect the grass collection bag
for signs of wear and replace immediately
with a genuine Yard Force part if damage is
found.
• Replace excessively worn or damaged parts
immediately.
Lubrication
All of the bearings in this product are lubricated
with a sufficient amount of high grade lubricants
for the life of the unit under normal operation
conditions. Therefore, no further lubrication of
the bearings is needed.
Ensuring a clean cut
WARNING!
The steel blades are extremely
sharp. To avoid injury, do not touch
the blades while making adjustments.
Misalignment of the blades can occur,
which often results from blades that are
either too loose or too tight. This can cause
an uneven cut or difficulty pushing the
mower.
1. Place the mower on a flat surface. Remove
the handles and the grass collection bag.
Turn the mower upside down to expose the
blades and the cutting bar.
2. Insert a piece of paper between the steel
blades and the cutting bar, then slowly turn
the wheel by hand (Fig. 17).
Fig. 17
Paper
Turn the
wheel by
hand
Cutting bar
Steel blade
3. All the blades should slice the paper evenly
along the entire length of the cutting bar while
the wheel is turned smoothly. Repeat this
testing on the other side of the mower.
4. If the mower cuts the paper intermittently,
use the hex key wrench provided to tighten
the adjustment bolt closest to where the
intermittent cut was observed. Tighten the
bolt on the appropriate end of the cutting bar
by turning it clockwise approximately 1/8th
of a turn until the steel blade contacts the
cutting bar (Fig. 18).
Adjusting
bolts
Hex key
Fig. 18
5. If it becomes too difficult to move the wheel
by hand while adjusting the reel blades, back
off the adjustment bolt slightly by turning
it counterclockwise. Test again with a new
piece of paper to verify proper cutting action.
6. Make the same adjustment at the other end
of the cutting bar.
WARNING!
Both adjustment bolts should
have tension on final adjustment. Do not
overtighten the adjustment bolts as this
could damage the blades.
NOTE:
If you have any questions, please call the
Yard Force Support Center toll-free at
(866) 902-9690 for assistance.
Cleaning and Storage
1. Clean the exterior of the machine thoroughly
using a soft brush and cloth before storing.
Do not use water, solvents, or polishes.
2. Turn the mower on its side to clean the blade
area.
WARNING!
Do not place your hands inside
or near the cutting area. If grass cuttings
are compacted in the blade area, remove
them using a wood or plastic cleaning tool
appropriate for blade cleaning.
3. Store the mower in a dry place. Do not place
other objects on top of the mower during
storage.
Maintenance Tips
Reel mowers are relatively low maintenance. For
consistent cutting, follow the below instructions:
• Always keep the cutting blades properly
adjusted. Refer to the instruction manual for
further directions.
• Regularly clean and lubricate cutting edges
with light spray oil.
IMPORTANT!
Reel mowers have difficulty cutting
tall weeds, such as dandelions, and will often
bend, rather than cut, such weeds. Cut often to
prevent this.
Disposal
Recycling the tool
• Do not dispose of electrical appliances as
unsorted municipal waste. Use separate
collection facilities.
