CABLE ROUTING
2-40
1. Hydraulic unit
2. Rear frame
3. Brake fluid reservoir
4. Frame
5. Brake hose (rear brake master cylinder to
hydraulic unit)
6. Rear wheel sensor lead
7. Rear brake master cylinder
8. Swingarm assembly
9. Rear wheel sensor lead cover
10. Rear wheel sensor protector
11. Rear wheel sensor
12. Rear brake caliper
13. Brake hose (hydraulic unit to rear brake caliper)
14. Brake fluid reservoir hose
15. Hydraulic unit brake pipe (hydraulic unit to rear
brake caliper)
16. Hydraulic unit brake pipe (rear brake master
cylinder to hydraulic unit)
17. Rear brake hose bracket
18. Rear fender
A. Make sure that the rear wheel sensor lead does
not protrude from the rear wheel sensor lead cover.
B. Route the rear wheel sensor lead between the
swingarm assembly and the rear wheel sensor
lead cover.
C. 59.3
°
D. 57.3
°
E. Install the holder 0–10 mm (0–0.39 in) from the slit
in the brake hose protector.
F. Position the holder as shown in the illustration.
G. Route the rear wheel sensor lead to the rear of the
brake hose (hydraulic unit to rear brake caliper).
H. Position the holder 0–10 mm (0–0.39 in) from the
top edge of the brake hose protector.
I.
Fasten the rear wheel sensor lead under the white
tape on the lead with the holder.
J. Install the larger diameter side of the holder on the
metal fitting section of the brake hose (rear brake
master cylinder to hydraulic unit).
K. Fasten the grommet on the rear wheel sensor lead
with the holder.
L. Fasten the grommet on the rear wheel sensor lead
with the holder on the rear wheel sensor lead
cover.
M. Fasten the grommet on the rear wheel sensor lead
with the holder on the rear wheel sensor protector.
N. Fasten the rear wheel sensor lead with the holder
on the rear wheel sensor protector.
O. Route the brake hose (hydraulic unit to rear brake
caliper) between the rear brake hose holder and
the swingarm assembly.
P. Fasten the brake hose (hydraulic unit to rear brake
caliper) with the holder. Face the catch of the
holder upward.
Summary of Contents for YZF-R1 2020
