Yamaha YFM35FGX Owner'S Manual Download Page 111 | Manualshive

Page: 111 / 156

background image

8-25

8

CAUTION:

ECB00480

The carburetor has been set and extensively
tested at the Yamaha factory. Changing these
settings without sufficient technical knowl-
edge may result in poor performance of or
damage to the engine.

EBU24000

Adjusting the engine idling speed

The engine idling speed must be checked and, if
necessary, adjusted as follows at the intervals
specified in the periodic maintenance and lubrica-
tion chart.

NOTE:

A diagnostic tachometer is needed to make this
adjustment.

1. Start the engine and warm it up.

NOTE:

The engine is warm when it quickly responds to the
throttle.

2. Attach the tachometer to the spark plug lead.
3. Check the engine idling speed and, if neces-

sary, adjust it to specification by turning the
throttle stop screw at the carburetor. To in-

crease the engine idling speed, turn the throt-
tle stop screw in direction (a), and to decrease
it, turn the screw in direction (b).

NOTE:

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U5UH15E0.book Page 25 Thursday, April 5, 2007 9:49 AM

«
...
109
110
111
112
113
...
»

Summary of Contents for YFM35FGX





























































































































































Reviews:

No comments

Related manuals for YFM35FGX

Brand: cascade corporation Pages: 16

Brand: TOMCAR Pages: 22

Brand: Yamaha Pages: 34

Brand: Yamaha Pages: 180

Brand: AAA Pages: 165

500 MXU IRS 4X4 NAKED EFI

Brand: KYMCO Pages: 1

Brand: Yamaha Pages: 24

Brand: Yamaha Pages: 95

Brand: Textron Pages: 56

Challenger 300EX

Brand: TrailMaster Pages: 19

Brand: ShoreLand'r Pages: 17

MAX Mk II Dumper

Brand: Muck-Truck Pages: 30

Brand: CF MOTO Pages: 179

Brand: Arctic Cat Pages: 102

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands