Yamaha YFM35FGX Owner'S Manual Download Page 21 | Manualshive

Page: 21 / 156

background image

4-2

4

EBU17813

Indicator lights and warning light

EBU17830

Reverse indicator light “

”

This indicator light comes on when the transmis-
sion is in the reverse position.

EBU17860

Neutral indicator light “

”

This indicator light comes on when the transmis-
sion is in the neutral position.

EBU26931

Oil temperature warning light “

”

This warning light comes on when the engine over-
heats. When this occurs, stop the engine as soon
as it is safe to do so, and allow it to cool.
The electrical circuit of the warning light can be
checked by turning the key to “ON”, with the engine
stop switch set to “

”, and then pushing the start

switch.
If the warning light does not come on while the start
switch is being pushed, then go off after the start
switch is released, have a Yamaha dealer check
the electrical circuit.
If the warning light stays on, allow the engine to
cool. If the warning light stays on when the engine
is cool, have a Yamaha dealer check the electrical
circuit.

CAUTION:

ECB00010

●

The engine may overheat if the ATV is over-
loaded. In this case, reduce the load to spec-
ification.

●

Start the engine after making sure that the
warning light is out. Continuous use while
the warning light is on may cause damage to
the engine.

1. Neutral indicator light “N”
2. Reverse indicator light “R”

3. On-Command four-wheel-drive indicator light “

”

4. Oil temperature warning light “

”

U5UH15E0.book Page 2 Thursday, April 5, 2007 9:49 AM

«
...
19
20
21
22
23
...
»

Summary of Contents for YFM35FGX





























































































































































Reviews:

No comments

Related manuals for YFM35FGX

Brand: Club Car Pages: 20

Brand: Aosom Pages: 5

Brand: Strongway Pages: 3

Brand: PRONAR Pages: 166

Brand: Jianshe Pages: 52

Brand: Camoplast Pages: 55

Renegade 570 2016

Brand: Can-Am Pages: 534

Brand: Yamaha Pages: 59

2007 HUV 4213-G

Brand: Husqvarna Pages: 48

Brand: Precision Pages: 9

MAX Mk II Dumper

Brand: Muck-Truck Pages: 30

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands