Yamaha YFM35FGX Owner'S Manual Download Page 48

Page: 48 / 156

6-4

3. Open the throttle lever gradually.

Shifting: Reverse

1. Bring the ATV to a complete stop.
2. Apply the brake pedal.
3. Shift from neutral to reverse and vice versa by

moving the drive select lever along the shift
guide.

NOTE:

When in reverse, the reverse indicator light should
come on. If the indicator light does not come on,
have a Yamaha dealer check the electrical circuit.

4. Check behind for people or obstacles, and

then release the brake pedal.

5. Open the throttle lever gradually and continue

to watch to the rear while backing.

1. Drive select lever
2. F (Forward)

3. N (Neutral)

4. R (Reverse)

1. Drive select lever

2. F (Forward)

3. N (Neutral)
4. R (Reverse)

U5UH15E0.book Page 4 Thursday, April 5, 2007 9:49 AM

Summary of Contents for YFM35FGX





























































































































































Search results

Summary of Contents for YFM35FGX

Reviews:

Related manuals for YFM35FGX

Brands by name

Popular brands

Yamaha YFM35FGX, Owner'S Manual

Search results

Summary of Contents for YFM35FGX

Reviews:

Related manuals for YFM35FGX

Brands by name

Popular brands