Yamaha YFM35FGX Owner'S Manual Download Page 22

Page: 22 / 156

4-3

EBU17952

On-Command four-wheel-drive indicator light
“

”

This indicator light comes on when the On-Com-
mand four-wheel-drive switch is set to the “4WD”
position.

NOTE:

Due to the synchronizing mechanism in the differ-
ential gear case, the light may not come on until
the ATV starts moving.

EBU18061

Handlebar switches

EBU18080

Engine stop switch “

”

Set this switch to “

” before starting the engine.

The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to “

”.

EBU18100

Start switch “

”

Push this switch to crank the engine with the start-
er.

CAUTION:

ECB00050

See the starting instructions on page 6-1 prior
to starting the engine.

EBU18151

Light switch “

/OFF”

Set this switch to “

” to turn on the low beams

and the taillight. Set the switch to “

” to turn on

the high beams and the taillight. Set the switch to
“OFF” to turn off all the lights.

1. Light switch “

/OFF”

2. Engine stop switch “

”

3. Start switch “

”

U5UH15E0.book Page 3 Thursday, April 5, 2007 9:49 AM

Summary of Contents for YFM35FGX





























































































































































Search results

Summary of Contents for YFM35FGX

Reviews:

Related manuals for YFM35FGX

Brands by name

Popular brands

Yamaha YFM35FGX, Owner'S Manual

Search results

Summary of Contents for YFM35FGX

Reviews:

Related manuals for YFM35FGX

Brands by name

Popular brands