manualshive.com logo in svg

Yamaha YFM350RZ, Owner'S Manual

The Yamaha YFM350RZ Owner's Manual is a comprehensive guide that provides essential information on operating and maintaining this exceptional ATV. Easily downloadable from our website, it is available for free. Visit manualshive.com to access this manual and enjoy hassle-free riding experiences with your Yamaha YFM350RZ.

Share
Download
background image

8-19

8

4. Insert the tailpipe into the muffler and align the

bolt holes.

5. Install the bolt and tighten it to the specified

torque.

6. Remove the purging bolt.

7. Start the engine and rev it up approximately

twenty times while momentarily creating ex-
haust system back pressure by blocking the
end of the muffler with a shop towel.

8. Stop the engine and allow the exhaust pipe to

cool.

9. Install the purging bolt and tighten it to the

specified torque.

1. Tailpipe
2. Spark arrester

Tightening torque:

Tailpipe bolt:

10 Nm (1.0 m·kgf, 7.2 ft·lbf)

1. Purging bolt

Tightening torque:

Purging bolt:

27 Nm (2.7 m·kgf, 19 ft·lbf)

U1BS60E0.book  Page 19  Thursday, April 16, 2009  4:11 PM

Summary of Contents for YFM350RZ











































































































































Reviews:

No comments

Related manuals for YFM350RZ

Brands by name

Popular brands

Load more brands