Yamaha YFM350RZ Owner'S Manual Download

Page: 121 / 138

8-42

5. Install the headlight bulb holder by aligning the

projections with the holes in the headlight unit,
pushing it inward, and turning it clockwise until
it stops.

6. Install the headlight bulb holder cover at the

rear of the headlight.

NOTICE:

Make sure the

headlight bulb holder cover is securely fit-
ted over the bulb holder and seated prop-
erly.

[ECB00671]

7. Adjust the headlight beam if necessary.

EBU25561

Adjusting a headlight beam

NOTICE

ECB00690

It is advisable to have a Yamaha dealer make
this adjustment.

To raise a headlight beam, turn the headlight beam
adjusting bolt in direction (a).
To lower a headlight beam, turn the adjusting bolt
in direction (b).

1. Headlight beam adjusting bolt

U1BS60E0.book Page 42 Thursday, April 16, 2009 4:11 PM

Summary of Contents for YFM350RZ











































































































































Search results

Summary of Contents for YFM350RZ

Reviews:

Related manuals for YFM350RZ

Brands by name

Popular brands

Yamaha YFM350RZ, Owner'S Manual

Search results

Summary of Contents for YFM350RZ

Reviews:

Related manuals for YFM350RZ

Brands by name

Popular brands