Yamaha YFM350RZ Owner'S Manual Download | Manualshive

Page: 54 / 138

background image

6-7

6

EBU20722

Parking

When parking the ATV, shift into first gear, stop the
engine, apply the parking brake, and then turn the
fuel cock to “OFF”.

EBU20903

Parking on a slope

WARNING

EWB00850

Avoid parking on hills or other inclines. Park-
ing on a hill or other incline could cause the
ATV to roll out of control, increasing the
chance of an accident. If you must park on an
incline, place the ATV transversely across the

incline, shift into first gear, stop the engine, ap-
ply the parking brake, and then block the front
and rear wheels with rocks or other objects.
Do not park the ATV at all on hills that are so
steep you could not walk up them easily.

1. Bring the ATV to a stop by applying the front

brake, shift into first gear, and then stop the
engine.

2. With the front and rear brakes applied, apply

the parking brake.

3. Release the front and rear brakes.

1. Locked position

U1BS60E0.book Page 7 Thursday, April 16, 2009 4:11 PM

«
...
52
53
54
55
56
...
»

Summary of Contents for YFM350RZ











































































































































Reviews:

No comments

Related manuals for YFM350RZ

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands