manualshive.com logo in svg

Yamaha YFM350RZ, Owner'S Manual

The Yamaha YFM350RZ Owner's Manual is a comprehensive guide that provides essential information on operating and maintaining this exceptional ATV. Easily downloadable from our website, it is available for free. Visit manualshive.com to access this manual and enjoy hassle-free riding experiences with your Yamaha YFM350RZ.

Share
Download
background image

4-4

4

2. To increase the maximum engine power avail-

able and the maximum speed of the ATV, turn
the adjusting screw in direction (a). To de-
crease the maximum engine power available
and the maximum speed of the ATV, turn the
adjusting screw in direction (b). Do not turn
the adjusting screw out more than 12 mm
(0.47 in) or the throttle cable could be dam-
aged. Always make sure the throttle lever free
play is adjusted to 2.0–4.0 mm (0.08–0.16 in).
(See page 8-21.) 

WARNING! Improper ad-

justment of the speed limiter and throttle
could cause throttle cable damage or im-
proper throttle operation. You could lose
control, resulting in an accident.

 [EWB00241]

3. Tighten the locknut.

EBU18382

Clutch lever 

The clutch lever is located on the left handlebar
and the ignition circuit cut-off system is incorporat-
ed in the clutch lever holder. To disengage the
clutch, pull the clutch lever toward the handlebar
grip. To engage the clutch, release the clutch lever.
The clutch lever should be pulled rapidly and re-
leased slowly for smooth clutch operation. (See
page 6-1 for a description of the ignition circuit cut-
off system.)

1. Locknut
2. Adjusting screw

3. No more than 12 mm (0.47 in)

U1BS60E0.book  Page 4  Thursday, April 16, 2009  4:11 PM

Summary of Contents for YFM350RZ











































































































































Reviews:

No comments

Related manuals for YFM350RZ

Brands by name

Popular brands

Load more brands