Yamaha YFM350RZ Owner'S Manual Download

Page: 27 / 138

4-2

EBU17792

Indicator lights

EBU17830

Reverse indicator light “

”

This indicator light comes on when the transmis-
sion is in the reverse position.

EBU17860

Neutral indicator light “

”

This indicator light comes on when the transmis-
sion is in the neutral position.

EBU18061

Handlebar switches

EBU18080

Engine stop switch “

”

Set this switch to “

” before starting the engine.

The engine stop switch controls the ignition and
stops the engine when it is running. Use this switch
to stop the engine in an emergency situation. The
engine will not start or run when this switch is set
to “

”.

1. Reverse indicator light “R”

2. Neutral indicator light “N”

1. Light switch “

/OFF”

2. Engine stop switch “

”

3. Start switch “

”

U1BS60E0.book Page 2 Thursday, April 16, 2009 4:11 PM

Summary of Contents for YFM350RZ











































































































































Search results

Summary of Contents for YFM350RZ

Reviews:

Related manuals for YFM350RZ

Brands by name

Popular brands

Yamaha YFM350RZ, Owner'S Manual

Search results

Summary of Contents for YFM350RZ

Reviews:

Related manuals for YFM350RZ

Brands by name

Popular brands