manualshive.com logo in svg

Yamaha XL700 WaveRunner 2003, Owner'S/Operator'S Manual, Page: 93 / 117

Share
Download
Yamaha XL700 WaveRunner 2003 Owner'S/Operator'S Manual Download Page 93

4-14

E

EJU01342 

Cleaning and adjusting the 
spark plugs  

The spark plug is an important engine

component and is easy to inspect. The con-
dition of the spark plug can indicate some-
thing about the condition of the engine. For
example, if the center electrode porcelain is
very white, this could indicate an intake air
leak or carburetion problem in that cylinder.
Do not attempt to diagnose any problems
yourself. Have a Yamaha dealer service the
watercraft. 

Remove and inspect the spark plug peri-

odically; heat and deposits will cause the
spark plug to slowly break down and erode.
If electrode erosion becomes excessive, or if
carbon and other deposits are excessive,
replace the spark plug with the specified
plug. 

Measure the spark plug gap 

a

 with a

wire thickness gauge before installing the
spark plug. Adjust the gap to specification if
necessary. 

To reinstall spark plug: 

1. Clean the gasket surface. 
2. Wipe any dirt from the threads of the

spark plug. 

3. Screw the spark plug to the correct

torque. 

Standard spark plug: BR8HS 

Spark plug gap: 

0.6–0.7 mm (0.024–0.028 in) 

Spark plug torque: 

25 N·m (2.5 kgf·m, 18 ft·lb) 

UF0M14.book  Page 14  Wednesday, July 31, 2002  2:30 PM

Summary of Contents for XL700 WaveRunner 2003






















































































































Reviews:

No comments