manualshive.com logo in svg

Yamaha XL700 WaveRunner 2003, Owner'S/Operator'S Manual, Page: 51 / 117

Share
Download
Yamaha XL700 WaveRunner 2003 Owner'S/Operator'S Manual Download Page 51

3-6

E

EJU01048 

Pre-operation check points 

EJU01728  

Engine compartment  

Ventilate the engine compartment before

each use. 

To ventilate the engine compartment,

remove the front seat and front storage com-
partment. (See page 2-5 for front seat, and
2-15 for front storage compartment.) Allow
the engine compartment to remain open for
a few minutes to allow any fuel vapors to
escape. Also, check for loose electrical con-
nections. 

WARNING

@ 

Failure to ventilate the engine compart-
ment could result in fire or explosion. Do
not start the engine if there is a fuel leak
or a loose electrical connection. 

@

EJU01242 

Fuel and oil systems  

Check the fuel system for leakage, cracks

or malfunctions before each use. (See page
4-9 for check points and correct proce-
dures.) 
1. Remove the fuel tank filler cap to release

any pressure that might have built up in
the fuel tank. 

2. Remove all seats and front storage com-

partment. (See pages 2-4 and 2-5 for
front and rear seat, and 2-15 for front
storage compartment.) 

3. Check the fuel and oil levels in the tanks

and replenish if necessary. (See pages
3-3 and 3-4 for filling instructions.)

UF0M14.book  Page 6  Wednesday, July 31, 2002  2:30 PM

Summary of Contents for XL700 WaveRunner 2003






















































































































Reviews:

No comments