Yamaha XL700 WaveRunner 2003 Owner'S/Operator'S Manual Download

Page: 68 / 117

3-23

EJU01075

Boarding and starting in deep
water

WARNING

●

Operator and passenger should prac-
tice getting on board in shallow water
before riding in deep water. Boarding
in deep water requires more skill.

●

The fatigue and exposure that could
result after unsuccessful attempts to
get back on the watercraft may
increase the risk of injuries and drown-
ing.

EJU01838

Boarding alone

1. Swim to the rear of the watercraft and

place both hands on the boarding plat-
form, pull yourself up, and then grasp the
handgrip with one hand.

2. Pull yourself up to a kneeling position on

the platform, and then move to the seat
and sit astride.

3. Attach the engine shut-off cord to your

left wrist, and then install the clip to the
engine shut-off switch.

4. Grip the handlebars firmly with both

hands, place both feet on the floor of the
footwell, start the engine, and then look
in all directions before starting off.

WARNING

Before starting off, make sure that there
are no boats, obstructions, or swimmers
around you.

UF0M14.book Page 23 Wednesday, July 31, 2002 2:30 PM

Summary of Contents for XL700 WaveRunner 2003






















































































































Search results

Summary of Contents for XL700 WaveRunner 2003

Reviews:

Related manuals for XL700 WaveRunner 2003

Brands by name

Popular brands

Yamaha XL700 WaveRunner 2003, Owner'S/Operator'S Manual

Search results

Summary of Contents for XL700 WaveRunner 2003

Reviews:

Related manuals for XL700 WaveRunner 2003

Brands by name

Popular brands