manualshive.com logo in svg

Yamaha XL700 WaveRunner 2003, Owner'S/Operator'S Manual, Page: 84 / 117

Share
Download
Yamaha XL700 WaveRunner 2003 Owner'S/Operator'S Manual Download Page 84

4-5

E

Top off the fuel tank with fresh gasoline

and add one ounce of Yamaha Fuel Stabi-
lizer and Conditioner to each gallon of fuel.

NOTE:

@ 

Use of Yamaha Fuel Stabilizer and Condi-
tioner eliminates the need to drain the fuel
system. If the fuel system is to be drained
instead, consult a Yamaha dealer. 

@

EJU01970 

Battery 

If the watercraft will not be used for more

than a month, disconnect the negative (–)
lead first, then the positive (+) lead and
breather hose, and then remove the battery
from the watercraft. 

Clean the battery casing using fresh

water. 

If the battery terminals are dirty or cor-

roded, clean them with a wire brush. 

Fully charge the battery, and then store it

in a cool, dark place. 

Apply Yamaha marine grease or Yamaha

grease A to the battery terminals. 

Check the battery at least every 2 months

and fully charge it if necessary.

WARNING

@ 

Be sure to connect the breather hose to
the battery. Fire or explosion could result
if the breather hose is damaged,
obstructed, or not connected properly. 

@

CAUTION:

@ 

The battery may not be usable again if
you store it for a long period without
charging it. Charge the battery periodi-
cally. 

@

UF0M14.book  Page 5  Wednesday, July 31, 2002  2:30 PM

Summary of Contents for XL700 WaveRunner 2003






















































































































Reviews:

No comments