Yamaha XL700 WaveRunner 2003 Owner'S/Operator'S Manual Download

Page: 36 / 117

2-9

EJU01015

Engine stop switch

Push this switch

(red button) to stop

the engine normally.

EJU01016

Engine shut-off switch

Insert the clip

, on the end of the engine

shut-off cord

, under the engine shut-off

switch

(black button). The engine will stop

automatically when the clip is removed from
the switch, such as if the operator falls off
the watercraft.

WARNING

●

Always attach the engine shut-off cord
to your wrist and the clip to the engine
shut-off switch BEFORE starting the
engine.

●

To prevent accidental starting of the
engine or unauthorized use by chil-
dren or others, always remove the clip
from the shut-off switch when the
engine is not running.

EJU01215

Choke knob

Starting a cold engine requires a richer

air-fuel mixture, which is supplied by the
choke.

Pull the knob

out to turn the choke on.

Push the knob in to turn the choke off.

UF0M14.book Page 9 Wednesday, July 31, 2002 2:30 PM

Summary of Contents for XL700 WaveRunner 2003






















































































































Search results

Summary of Contents for XL700 WaveRunner 2003

Reviews:

Related manuals for XL700 WaveRunner 2003

Brands by name

Popular brands

Yamaha XL700 WaveRunner 2003, Owner'S/Operator'S Manual

Search results

Summary of Contents for XL700 WaveRunner 2003

Reviews:

Related manuals for XL700 WaveRunner 2003

Brands by name

Popular brands