Yamaha XL700 WaveRunner 2003 Owner'S/Operator'S Manual Download Page 60 | Manualshive

Page: 60 / 117

Yamaha XL700 WaveRunner 2003 Owner'S/Operator'S Manual Download Page 60

3-15

E

EJU01137

Starting the engine

WARNING

@

Never start the engine or let it run for any
length of time in an enclosed area.
Exhaust fumes contain carbon monox-
ide, a colorless, odorless gas that may
cause loss of consciousness and death
within a short time. Always operate the
watercraft in an open area.

@

1. Launch the watercraft in water free from

weeds and debris and at least 60 cm
(2 ft) deep.

WARNING

@

Never operate in water that is less than
60 cm (2 ft) deep, otherwise you increase
your chance of hitting a submerged
object, which could result in injury.

@

CAUTION:

@

Never operate in water that is less than
60 cm (2 ft) deep, otherwise pebbles or
sand could be sucked into the jet intake,
causing impeller damage or engine over-
heating.

@

UF0M14.book Page 15 Wednesday, July 31, 2002 2:30 PM

«
...
58
59
60
61
62
...
»

Summary of Contents for XL700 WaveRunner 2003






















































































































Reviews:

No comments