Yamaha XJR1300 2007, Service Manual

Page: 59 / 386

CABLE ROUTING
2-36
1. Throttle cable
2. Ignition coil #1, #4
3. Horn (right side)
4. Neutral switch coupler
5. Pickup
coupler
6. Sidestand switch coupler
7. Fuel sender coupler
8. Fuel pump coupler
9. Throttle body (6P) coupler
10. Flasher relay
11. Reservoir tank
12. Headlight relay
13. Starting circuit cut-off relay
14. Starter motor cable
15. Starter relay
16. Seat rail
17. ECU
18. Rear fender rib
19. Rear flasher right
20. Taillight bracket
21. Rear flasher left
22. Seat lock cable
23. Seat lock
24. Positive battery lead
25. Lean angle sensor
26. Battery
27. Battery band
28. Fuse box
29. Throttle position sensor lead
30. Throttle position sensor
31. Horn (left side)
32. Ignition coil #2, #3
33. Tail/brake light coupler
34. Rear fender rib
35. Taillight lead
36. Wire harness
37. Rear fender
38. Rear flasher left lead
39. Rear flasher right lead
40. Starter relay lead
41. Protector
42. Wire harness protector
A. Horn (H mark sticker) should be attached to the
right.
B. Install high tension cords #1~#4 without mistak-
ing the numbers.
C. Fasten the throttle body (6P) coupler lead to the
cross tube of the frame with a band.
D. The ground lead should be tightened together
with air filter installation.
E. Fasten the positive battery leads (x 2) to the
wire harness with the battery band.
F. The wire harness, taillight lead, and rear flasher
leads left and right should be set between the
tail light bracket and rear fender rib.
G. The seat lock cable should not protrude from
the bracket.
H. Fasten the wire harness clamp to the rear
fender.
I. Route the sub harness past the front side of the
starting circuit cutoff relay.
J. Fasten the wire harness to the seat rail immedi-
ately to the back of the seat rail side cover
mounting bracket. Fasten forward of the EXUP
lead and O
2
sensor lead branch point. Band
end should face downward to the inside of the
back stay.
K. Fit the wire harness plug clamp to the T stud.
L. High tension cords in the order #1~#4 from the
left.
M. Fasten the wire harness and starter cable on
the harness positioning tape to the tank rail with
a band. The band end should face downwards.
The wire harness should not be entangled with
the T stud clamp.
N. Fasten the taillight lead and license plate light
lead to the taillight bracket with a clamp.
O. To taillight
P. The wire harness, taillight lead and rear flasher
leads left/right should not protrude above rear
fender rib height.
Q. To license plate light
R. Route the wire harness between the mounting
position of the rear fender to the frame and the
rib of the storage space.
S. Fasten the protector and wire harness protector
to the rear fender with rivets.
T. Route the left/right rear flasher through the
holes in the rear fender.
U. The starter motor cable should be fitted pulling
it at about 45 degrees towards the outside.
V. The positive battery lead should be fitted with
the crimping side facing downward.
W. Set the connector cover between frame cross
members with its opening facing the inside of
the vehicle. The fasten should be on the inside
with the ends following the air filter.
X. Fasten the throttle body lead to the seat rail with
a band. The fasten with a band should face
downwards with the ends following the air filter
surface.
Y. Install the positive battery lead so that the wir-
ing protrudes facing downward.
Z. The wire harness, taillight lead, left rear flasher
light lead and right generator coupler should be
stowed in the wire harness protector.
AA. The protector should be installed at the front of
the taillight bracket.
AB. After including all leads, bind the wire harness
protector with a Velcro strip (hooks facing
upwards).