manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 95 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 95

8-24

8

TIP

If the specified idling speed cannot be obtained as
described above, have a Yamaha dealer make the
adjustment.

EBU24044

Adjusting the throttle cable free play 

The throttle cable free play should be checked
and, if necessary, adjusted at the intervals speci-
fied in the periodic maintenance and lubrication
chart.
The throttle cable free play should measure 3.0–
5.0 mm (0.12–0.20 in) at the throttle lever. Period-
ically check the throttle cable free play and, if nec-
essary, adjust it as follows.

TIP

The engine idling speed must be checked, and ad-
justed if necessary, before adjusting the throttle ca-
ble free play.

1. Loosen the locknut.
2. To increase the throttle cable free play, turn

the throttle cable free play adjusting bolt in di-
rection (a). To decrease the throttle cable free
play, turn the adjusting bolt in direction (b).

1. Throttle stop screw

Engine idling speed:

1450–1550 r/min

U3D563E0.book  Page 24  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments