manualshive.com logo in svg

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 107 / 128

Share
Download
Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 107

8-36

8

To store the battery

●

If the ATV will not be used for more than one
month, remove the battery, fully charge it, and
then place it in a cool, dry place.

●

If the battery will be stored for more than two
months, check it at least once a month and fully
charge it if necessary.

To install the battery

TIP

Be sure the battery is fully charged.

1. Place the battery in its compartment.
2. Connect the positive battery lead first, then

connect the negative battery lead by installing
their bolt.

3. Install the battery holding plate by installing

the bolts.

4. Install the seat. (See page 4-11.)

NOTICE

ECB00632

●

Always keep the battery charged. Storing a
discharged battery can cause permanent
battery damage.

●

To charge a VRLA (Valve Regulated Lead Ac-
id) battery, a special (constant-voltage) bat-
tery charger is required. Using a
conventional battery charger will damage

1. Positive battery lead (red)
2. Negative battery lead (black)

U3D563E0.book  Page 36  Monday, May 12, 2008  11:12 AM

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments