Home
/
Yamaha
/
WOLVERINE 350 YFM35XY
/
Owner'S Manual

Yamaha WOLVERINE 350 YFM35XY, Owner'S Manual, Page: 91 / 128

Share

Page: 91 / 128

Yamaha WOLVERINE 350 YFM35XY Owner'S Manual Download Page 91

8-20

8

NOTICE

ECB00440

Do not twist the sponge material when squeez-
ing it.

8. Check the sponge material and replace it if

damaged.

9. Apply a quality foam air filter oil to the sponge

material.

TIP

The sponge material should be wet but not drip-
ping.

10. Pull the sponge material over the air filter ele-

ment frame, and then install the lock plate.

11. Insert the air filter element into the air filter

case, and then install the air filter case cover
by hooking the holders onto the air filter case.

12. Install the seat.

TIP

The air filter element should be cleaned every 20–
40 hours. It should be cleaned and lubricated more
often if the ATV is operated in extremely dusty ar-
eas. Each time the air filter element maintenance
is performed, check the air inlet of the air filter case
for obstructions. Check the air filter case rubber
joint to the carburetor fittings and the rubber joint
manifold fittings for an air-tight seal. Tighten all fit-
tings securely to avoid the possibility of unfiltered
air entering the engine.

NOTICE

ECB00460

●

Make sure that the air filter element is prop-
erly seated in the air filter case.

●

Never operate the engine with the air filter el-
ement removed. This will allow unfiltered air
to enter the engine, causing rapid engine
wear and possible engine damage. Addition-
ally, operation without the air filter element

U3D563E0.book Page 20 Monday, May 12, 2008 11:12 AM

«
...
89
90
91
92
93
...
»

Summary of Contents for WOLVERINE 350 YFM35XY

































































































































Reviews:

No comments